sunjoe CJ601E-RM Operator'S Manual Download

Page: 7 / 17

Know Your Electric Wood C Shredder

Read the owner’s manual and safety instructions carefully before operating the electric wood c shredder. Compare the

illustration below to the electric wood c shredder in order to become familiar with the location of the various controls and

adjustments. Save this manual for future reference.

Technical Data

Rated Voltage

120 V ~ 60 Hz

Motor

Electric

Power

14 A

Feed Type

Manual

No Load Speed

4100 ± 10% rpm

Cutting Diameter

1.5 in. (3.8 cm)

Decibel Rating

113 dB

Wheel Size

6 in. (15.2 cm)

Reduction Ratio

16:1

Hopper Dimensions

2 in. x 5 in. (5.1 cm x 12.7 cm)

Weight

25.4 lbs (11.5 kg)

1.  Paddle
2.  Hopper
3.  Main body
4.  Shredder stand assembly
5.  Wheel axle
6.  Wheel
7.  Paddle holder
8.  Appliance cord
9.  Motor

10. Reset button
11. Removable safety switch
12. Hopper locking knob

Summary of Contents for CJ601E-RM


















Search results

Summary of Contents for CJ601E-RM

Reviews:

Related manuals for CJ601E-RM

Brands by name

Popular brands

sunjoe CJ601E-RM, Operator'S Manual

Search results

Summary of Contents for CJ601E-RM

Reviews:

Related manuals for CJ601E-RM

Brands by name

Popular brands