background image

3

• 

Charger iCHRG40 is rated for 120 volt AC only – The 

charger must be plugged into an appropriate receptacle.

• 

Use only recommended attachments – Use of an 

attachment not recommended or sold by the battery 

charger or battery pack manufacturer may result in risk of 

fire, electric shock or personal injury.

• 

Unplug charger when not in use – Make sure to remove 

battery packs from unplugged chargers.

m

WARNING! 

To reduce the risk of electric shock, 

always unplug the charger before performing any cleaning 

or maintenance. Do not allow water to flow into the charger. 

Use a Ground Fault Circuit Interrupter (GFCI) to reduce shock 

hazards.

• 

Do not burn or incinerate battery packs – Battery packs 

may explode, causing personal injury or damage. Toxic 

fumes and materials are created when battery packs are 

burned.

• 

Do not crush, drop or damage battery packs – Do not 

use the battery pack or charger if they have sustained a 

sharp blow, been dropped, run over or have been damaged 

in any way (i.e. pierced with a nail, hit with a hammer, 

stepped on, etc.).

• 

Do not disassemble – Incorrect reassembly may pose 

a serious risk of electric shock, fire or exposure to toxic 

battery chemicals. If the battery or charger are damaged, 

contact an authorized Snow Joe

®

 + Sun Joe

®

 dealer or 

call the Snow Joe

®

 + Sun Joe

®

 customer service center at 

1-866-SNOWJOE (1-866-766-9563) for assistance.

• 

Battery chemicals cause serious burns – Never let a 

damaged battery pack contact the skin, eyes or mouth. 

If a damaged battery pack leaks battery chemicals, use 

rubber or neoprene gloves to safely dispose of it. If skin 

is exposed to battery fluids, wash the affected area with 

soap and water and rinse with vinegar. If eyes are exposed 

to battery chemicals, immediately flush with water for 20 

minutes and seek medical attention. Remove and dispose 

of contaminated clothing.

• 

Do not short circuit – A battery pack will short circuit if 

a metal object makes a connection between the positive 

and negative contacts on the battery pack. Do not place a 

battery pack near anything that may cause a short circuit, 

such as paper clips, coins, keys, screws, nails and other 

metallic objects. A short-circuited battery pack poses a risk 

of fire and severe personal injury.

• 

Store your battery pack and charger in a cool, dry 

place – Do not store the battery pack or charger where 

temperatures may exceed 104ºF (40ºC), such as in direct 

sunlight or inside a vehicle or metal building during the 

summer.

Information about the battery

NOTE: Model iONAIR-CT is compatible with the following 

battery packs (sold separately): iBAT40, iBAT40XR or 

iBAT40XRP.

1.  The battery packs ship partially charged, and must be 

charged completely before you use the tool for the first time.

2.  For optimum battery performance, avoid low discharge 

cycles by charging the battery pack frequently.

3. 

Store the battery pack in a cool place, ideally at 59°F 

(15°C) and charged to at least 40%.

4. 

Lithium-ion batteries are subject to a natural aging 

process. The battery pack must be replaced at the latest 

when its capacity falls to just 80% of its capacity when 

new. Weakened cells in an aged battery pack are no 

longer capable of meeting the high power requirements 

needed for the proper operation of your air compressor,  

and therefore pose a safety risk.

5. 

Do not throw battery packs into an open fire as this poses 

a risk of explosion.

6. 

Do not ignite the battery pack or expose it to fire.

7. 

Do not exhaustively discharge batteries. Exhaustive 

discharge will damage the battery cells. The most 

common cause of exhaustive discharge is lengthy storage 

or non-use of partially discharged batteries. Stop working 

as soon as the performance of the battery falls noticeably 

or the electronic protection system triggers. Place the 

battery pack in storage only after it has been fully charged.

8.  Protect batteries and the tool from overloads. Overloads 

will quickly result in overheating and cell damage inside 

the battery housing even if this overheating is not 

apparent externally.

9.  Avoid damage and shocks. Immediately replace batteries 

that have been dropped from a height of more than one 

meter or those that have been exposed to violent shocks, 

even if the housing of the battery pack appears to be 

undamaged. The battery cells inside the battery may have 

suffered serious damage. In such instances, please read 

the waste disposal information for proper battery disposal.

10. 

If the battery pack suffers overloading and overheating, 

the integrated protective cutoff will switch off the 

equipment for safety reasons.

 

IMPORTANT! Do not press the ON/OFF switch any more 

if the protective cut-off has been activated. This may 

damage the battery pack.

11. Use only original battery packs. The use of other batteries 

poses a fire risk and may result in injuries or an explosion.

Summary of Contents for iONAIR-CT

















Reviews: