background image

9

NOTE: If the top light remains green while the bottom light 

alternately flashes red and green, this indicates a temperature 

abnormality (i.e. that the battery pack is either too hot or too 

cold). If there is only a red blinking light, this indicates that 

something is wrong with the battery. Contact Snow Joe

®

 + 

Sun Joe

®

 customer service center at 1-866-SNOW-JOE 

 

(1-866-766-9563) for assistance.

5.  A fully discharged pack with an internal temperature 

in the normal range will fully charge in 2.5 to 3 hours 

(between 32ºF/0ºC and 113ºF/45ºC). Heavily cycled 

battery packs may take longer to charge completely.

6.  If the charging light indicator alternately blinks red and 

green or the light indicator does not come on at all, check 

that the battery pack is fully seated into the bay. Remove 

the pack and reinsert. If the problem persists, contact the 

Snow Joe

®

 + Sun Joe

®

 customer service center at  

1-866-SNOWJOE (1-866-766-9563) for assistance.

7.  When charging is complete, remove the battery from the 

charger by pulling the push lock button and sliding the 

battery backward to unlock it from the charger (Fig. 6).

8.  Timely recharging of the battery will help prolong the 

battery's life. You must recharge the battery pack when 

you notice a drop in the equipment's power.

IMPORTANT! Never allow the battery pack to become fully 

discharged as this will cause irreversible damage to the 

battery. 

Charging a Hot or Cold Battery Pack

A red and green flashing indicator light on the charger 

indicates that the battery pack temperature is outside the 

charging range. Once the pack is within the acceptable 

range, normal charging will take place and the red light will 

be continuous. Hot or cold battery packs may take longer to 

charge. 

Operation

Building Tank Pressure

1. 

Locate the air compressor on flat level surface to ensure 

proper pump lubrication and to prevent the damage to 

the unit. Keep at least 12 inches of space around the unit 

to allow air circulation. 

2.  Pull out the safety valve to check if it works properly  

(Fig. 7).   

IMPORTANT! If the safety valve does not work properly, 

over-pressurization may occur and cause an air tank rupture 

or explosion. Contact the Snow Joe

®

 + Sun Joe

®

 customer 

service center at 1-866-SNOWJOE (1-866-766-9563

) if the 

safety valve d

oesn't work well

.

3. 

Make sure the On/Off switch is in O (Off) position. Insert 

the battery (Fig. 8).  

Green

Flashing red/green

Temperature abnormal

Flashing red only

Something is wrong

Fig. 6

Push lock button

Battery Pack  

Temperature

Lithium-Ion Charging Status

Too hot

Flashing

Not charging

Normal range

Continuous

Normal charging

Too cold

Flashing

Not charging

Red Charger 

Indicator Light

Charging  

Status

Fig. 7

Safety valve

Summary of Contents for iONAIR-CT

















Reviews: