background image

© 2017 by Snow Joe

®

, LLC

All rights reserved. Original instructions.

SAVE THESE INSTRUCTIONS

1

A Division of Snow Joe

®

, LLC

Model SWJ805E

Form No. SJ-SWJ805E-880E-M

R

OPERATOR’S MANUAL

ELECTRIC POLE + CHAIN SAW

8-INCH | 6-AMP | 2-IN-1 POLE + HANDHELD

IMPORTANT!

Safety Instructions
All Operators Must Read These 

Instructions Before Use

Always follow these safety guidelines. Failure to do so may 

result in serious bodily injury or death.

m

DANGER! 

This indicates a hazardous situation, which,   

if not followed, will result in serious injury or death.

m

WARNING! 

This indicates a hazardous situation, which, 

if not avoided, could result in serious injury or death.

m

CAUTION! 

This indicates a hazardous situation, which, 

if not avoided, could result in minor or moderate injury.

General Safety 

m

WARNING!

 

When using electric yard tools, basic safety 

precautions should always be followed to reduce the risk of 

fire, electric shock, and personal injury, including the following:

1. Keep guards in place – Protective guards should be 

checked periodically to ensure they are properly fitted and 

in correct working order.

2. Remove adjusting keys and wrenches – Check that 

adjusting wrenches are removed from the saw before 

turning it on.

3. Keep work area clean and well-lit – Clear work area of 

branches and limbs after each cutting session. Cluttered 

areas invite accidents.

4.  Do not use in dangerous environments – Do not use 

power tools in damp or wet locations.

5.  Do not use the electric pole + chain saw in the rain.
6.  Keep bystanders and children away – 
All bystanders, 

including children and pets, should be kept a safe 

distance away from the work area.

7.  Do not force the tool – 

It will do the job effectively and 

safely if it is used at the rate for which it was designed. 

8.  Use the right tool – Do not force the tool or any 

attachment on the tool to do a job for which they were  

not designed. 

 9. Wear proper apparel – Do not wear loose articles of 

clothing or jewelry since such items may get caught in 

moving parts. Use of heavy-duty rubber gloves, 

  substantial non-skid footwear, and close-fitting clothing is 

recommended when working outdoors with power tools.

10. Wear protective hair coverings to contain long hair. 
11. Always wear safety glasses and ear defenders to 

provide eye and ear protection – Everyday eyeglasses 

only have impact resistant lenses and do not provide the 

same protection as safety glasses.

12. Wear face or dust masks – If the cutting operation is 

dusty, the use of a face or dust mask specially designed 

to filter out microscopic particles is recommended.

13. Do not overreach – Keep proper footing and balance  

at all times.

14. Maintain tools with care – Keep tools sharp and clean 

for best and safest performance. Follow instructions for 

lubricating and changing accessories. 

15. Disconnect tool – Disconnect the electric pole + chain 

saw from the power supply when not in use, before 

servicing, when transporting, or when changing the chain 

or other accessories.

16. Reduce the risk of unintentional starting – Make sure 

the switch is in the OFF position before plugging the tool 

into a power source.

17. Use recommended accessories – Consult the owner’s 

manual for recommended accessories. The use of 

improper accessories may cause risk of injury. 

18. Check for damaged parts – Before each use, repair, or 

replace any guard or part that is damaged. In addition, 

check for alignment of moving parts, binding of moving 

parts, breakage of parts, and any other conditions that 

may affect the tool's operation.

19. Never leave tool unattended while it is running – Turn 

the power OFF by removing the power cord directly from 

its socket. Do not leave the saw until the cutting bar 

comes to a complete stop.

20. Avoid unintentional starting – Do not carry the electric 

pole + chain saw with your finger on the switch.

21. Do not grasp the exposed cutting blade or cutting 

edges when picking up or holding the saw – Be sure  

to encase the cutting bar in its protective sheath when  

not in use.

22. Stay alert – Watch what you are doing. Use common 

sense. Do not operate the electric pole + chain saw when 

you are tired.

23. Store idle tool indoors – When not in use, appliances 

should be stored indoors in a dry and high or locked-up 

place out of the reach of children.

Summary of Contents for SWJ805E























Reviews: