Sunjoy L-GZ330PCO-1 Manual Download

Page: 1 / 13

Vineyard Swing

Item#: L-GZ330PCO-1

Congratulations on your purchase of our SUNJOY Vineyard Swing. Our clear, easy to follow,

step-by-step instructions will guide you through the assembly process from start to finish.

WARNING:

Read and follow all Warnings & Assembly Instructions before attempting to assemble.

Begin assembly not less than 6 feet from any obstruction such as a fence, garage, house,

overhanging branches, laundry line, or electrical wires.

Some parts may container sharp edges. Wear protective gloves as necessary.

Keep children away from assembly area.

Install on level ground.

Do not over tighten any of the bolts or nuts; tighten each bolt and nut until firm.

Check all nuts and bolts for tightness before and during usage.

This unit is heavy. Do not assemble this item alone.

IMPORTANT

Please take time to read these instructions thoroughly and follow each step carefully for safe and

easy operation. Keep this manual for future reference.

For technical assistance on assembly or replacement parts, call Sunjoy Industries at 1-866-578-6569

from 8:30AM to 5:30PM EST, or email us at sams@sunjoygroup.com for assistance.

Summary of Contents for L-GZ330PCO-1













