background image

Nov/06

                                                                     

                         

MN6000000014 

     

12

Using FDISK Under Windows® 2000/XP 

Note: The external hard disk can’t works with ‘Dynamic Disk’ 

type. Do not upgrade the external  hard  disk  to  ‘Dynamic  Disk’ 

type, always use it with ‘Basic Disk’ type. 

1.

 

To partition the external hard disk under Windows 2000 or 

Windows XP, please plug the external hard disk and make sure it 

is recognized, then.,

 

① 

In Windows 2000: Click 

Start 

Ö

 Settings 

Ö

 Control 

Panel 

Ö

 Administrative Tools 

Ö

 Computer 

Management 

to open 

‘Computer Management’ 

window.

 

② 

 In Windows XP: Click 

Start 

Ö

 Control Panel 

Ö

 

Performance and Maintenance 

Ö

 Administrative Tools 

Ö

 Computer Management 

to open 

‘Computer 

Management’ 

window.

 

 

 

2.

 

Click on 

‘Disk Management’ 

on the left part of this window, all 

connected disk drives will be listed in the right part. Find out the 

largest number of Disk #, for example, on the below picture, Disk 

is the largest number, and it is the external hard disk. On the 

right side of the Disk 

1

 is the status of the partitions of this disk 

drive, you can create a new or delete an exist partition by 

Summary of Contents for S-190
















Reviews: