background image

Only operate the wheelchair at a low and maneuverable

speed when the parallel swing-away is in use.

When transferring to and from the wheelchair, do not use

the 

armrest

 as a means of support.

Do not hang any items on or over the parallel swing-away

remote assembly as this could damage the swing-away

mechanism.

3.12 Power recline

 DANGER! 

Trap Point (p

inch 

p

oint

)

Avoid putting hands or fingers near the power recline 

mechanism while in operation.

Weight Capacity

The maximum user weight capacity for the power recline 

is up to 300 lbs (136 kg), 350 lbs (160 kg) for heavy duty 

chair.  Exceeding this weight capacity could lead to injury 

and/or permanent damage to the equipment.

3.13 Power leg

 

rest

 DANGER!

The power leg rest accessory has a maximum user weight 

capacity of up to 350 lbs (160 kg) depending on your 

system configuration. Never exceed this capacity while 

operating the powered actuator.

3.14 

T

ilt

 or tilt/lift combo

        

DANGER! 

Trap Point (pinch point)

Avoid putting hands, fingers, clothing items, or letting 

children near the seating system when the Tilt/Lift 

mechanism is in operation.

Weight Capacity

The powered lift/tilt modular accessory for this system 

has a maximum user weight capacity of up to 300 lbs

  

 

(136 kg).  The powered tilt modular accessory for this 

system has a maximum user weight capacity of up to 

   

350 lbs (160 kg). Never exceed this capacity while 

operating the powered actuator.

3.15 

C-ME®

 lift

        

DANGER!

 

CAUTION

!

3.1

6

 Swing away joystick arm

 DANGER! 

Before adjusting the swing-away arm, switch off the 

controller to avoid accidental displacement of the joystick 

which would cause unwanted movement of your 

wheelchair.  Be aware that the width of your chair may 

have increased and you may not be able to go through 

certain obstacles. 

T

he C-ME

 accessory

 has a maximum user weight 

capacity of up to 250 lbs (113 kg) 

with

 a maximum speed 

of 

3

mph

 or a maximum user weight of 300 lbs (136 kg) 

with a maximum speed of 2.4mph at full lift

.

  Never 

exceed this capacity while operating the lift.

WARNING

!

Exceeding these weight capacities could lead to injury 

and/or permanent damage to the equipment.

  

NOTE - 

Exceeding the weight limit will void the warranty.

Q700 M Ergo Seat

10

247554 Rev. A

Summary of Contents for Quickie Q700 M SEDEO ERGO

































Reviews: