background image

2.3.2 User 

and

 Attendants

2.3.1 User

1.

2.

3.

4. Have someone help you practice bending, reaching

and transfers until you learn how to do them safely.

5.

6.

7.
8.

9.

10.

11.

Never try a new maneuver on your own unless you are

sure it is safe.

Get to know the areas where you plan to use your

system. Look for hazards and learn how to avoid them.

Always wear a positioning strap.

Do not use a seating system if the joystick does not

spring back to the neutral position.

Do not use your seating system if the joystick boot is

ripped or damaged.

Do not try to tip this seating system without an

attendant present.

Do not allow additional riders, the system may become

unstable.

2.

3.

5

. Always keep your hands and body parts clear of moving

parts to help prevent injuries.

2.3 Safety: General warnings

Always ensure that you are able to operate all controls from

a comfortable position. Paying attention to your posture is

essential to ensure your continued comfort and well being.

Always make sure that you can be seen clearly. Use the

lights, especially if you intend using your seating system in

poor light.

This seating system has been set up to match the needs of a

particular user. If used by another user then it may need to

be adjusted.

Do not let children or others use your seating system.

Avoid spilling liquids on to the controller or its connections.

Especially hot, sticky, sugary or corrosive liquids. Such

contamination may compromise the safe operation of the

control system and damage the seating system upholstery.

  

DANGER! 

DANGER! 

Every seating system is different. 

Take the time to learn the feel of this system before 

you begin riding. 

Be aware that you must develop your own methods for 

the safe use of this system that are best suited to your 

level of function and ability.

1. 

 

 

  

DANGER! 

When transferring the user in or out of the seating  

system never use the footplate as a platform.

When transferring the user in or out of the seating  

system never use the 

a

rmrest as a means of support.

Do not lift this seating system by any parts that are  

removable, doing so may result in damage to the  

seating system or injury to the user.

Never try to stop or slow this seating system with  the 

wheel locks (if applicable). Wheel locks are  designed to 

prevent the system from moving when stopped. They 

are not brakes.

Wheelchairs involved in collisions should be replaced.  

NOTE- The warranty is void on any wheelchair that is 
involved in a collision.

 WARNING!

DO NOT use any wheelchair that has been involved in a motor 
vehicle accident. A sudden stop and/or collision may 
structurally damage your wheelchair. There may have been a 
change to  the structure of the chair, and/or damaged or 
broken some of the components. Wheelchairs involved in 
sudden stops should be inspected for possible failures in 
frame and/or components.   Frame damage may be 
represented by but not limited to: visual cracks, dents, metal 
distortion, bends, or damage to the seating mounting.  If the 
chair no longer drives straight, it could be damaged.  

If the 

wheelchair has been involved in an accident, discontinue use 
immediately and contact your Authorized Dealer for a 
thorough inspection.

  If damage is questionable or if there is 

concern regarding the condition of the chair, Sunrise Medical 
recommends replacement of the chair.

4

Q700 M Ergo Seat

6

247554 Rev. A

Summary of Contents for Quickie Q700 M SEDEO ERGO

































Reviews: