background image

108833 Rev. A

22

S - 6 3 6

X I .

4. Connect and disconnect battery cables with caution. Only

connect the charger to the power supply after the charger
has been connected to the chair.

5. Make sure to allow enough

time to fully charge batteries.

NOTE– 

Batteries should never be left for

long periods in the discharged
state. Unused or stored batter-
ies should be given a charge
once per month.

6. Charge batteries by engaging

the battery charger connector
(A) to the charg-
er/programming port (B)
located on the joystick.

F. DISPOSING OF BATTERIES

WARNING

1. All batteries once they have reached the end of their useful

life are deemed to be hazardous waste.

2. For further information on handling and recycling contact

your local recycling authority.

3. Always dispose of product through a recognized agent.

E. CHARGING BATTERIES

WARNING

To avoid the risk of severe injury or death from electri-
cal shock, fire or explosion while charging:

1. Never connect charger to a 240 volt source. The mains input

voltage is 110 volts.

2. Never touch the charger after it is connected to an electrical

outlet. This may cause electrical shock.

Never connect or disconnect charger from battery while
there is power to the charger.

3. Never use an extension cord. Use of an improper cord could

damage the charger, or cause a fire or electrical shock.

4. A battery emits explosive hydrogen gas during charging. To

reduce the risk of fire or explosion:

Make sure area is well vented. Never charge battery in a
closed-in area.

Never smoke or allow a spark, flame or high heat near
battery during charging.

Never allow metal tools or chair parts to make direct
contact across both terminals.

5. Never look directly into cells when charging battery.

Always:

1. Use the charger that comes with your wheelchair. Read and

follow all instructions and warnings. 

2. Make sure room is well ventilated. 
3. Turn off all power to your chair. 

Remote Joystick

A

B

Summary of Contents for QUICKIE S-636





























Reviews: