background image

10

System with no diverter

Diagram C-1

1.  Turn off your pool pump. Block the inlet and outlet of your pool so that the water won't empty

when you are connecting your panel(s).

2.  Remove the hose from the pool inlet ( hose between the filter and the pool ) and connect the
      hose to the panel inlet. If hose is too short, you need to purchase a new one. Make sure
      you purchase the appropriate size that is compatible with your existing pool equipment.
      For 1

1

/

4

" hose, it will only slide over the small end of the combination adapter. See Fig C1-1.

      For 1

1

/

2

" hose, it will slide all the way to flange of combination adapter. See Fig C1-2. Place

     metal collar 

1

/

4

" from edge and tighten collar with screwdriver. See Diagram C-1.

3.  Connect another hose (not supplied) from the panel outlet to the pool inlet. See Diagram C-1.

4.  Make sure that your hoses are all connected the correct way and that all the collars have been
      tightened. Unblock the inlet and outlet of your pool.

5.  Turn on your pool pump. Check for any leaks. If any of the threaded fittings leak, remove the
      fitting and apply more Teflon. If any of the hoses leak at the connection, loosen the collar and
      push the hose over the fitting and re-tighten the metal collar. You will see air bubbles coming
      from the pool inlet. This is normal and will stop once the air inside the panels has been purged.

Note: Without a diverter, your solar heating system is always ON. At night, your solar panels will cool your swimming pool.
           We recommend you close your pump at night to avoid this or purchase a diverter kit (SQ-DK)

System with diverter (part # SQ-DK)

Swimming Pool

Filter

Pump

Pool Outlet

Pool Inlet

To Panel
Inlet

From Panel
Outlet

Fig C1-1

Fig C1-2

Summary of Contents for SunQuest SPACE SAVER SQ-2210















Reviews: