SunStar KM-757 User Manual Download

Page: 8 / 35

Usage

Max sewing speed

Max no. of stitches

Needle bar stroke

Feed dog height

Manual

Knee

Automatic

Needle

Lubrication

Needle width gauge

Presser

foot height

Model Name

Item

KM-757BL-7N

KM-757BL-7S

KM-757BL

KM-757-7N

KM-757-7S

KM-757

Model No

Model Name

1) Sewing machine

KM-757

KM-757-7S

KM-757-7N

KM-757BL

KM-757BL-7S

KM-757BL-7N

KM-797

KM-797-7S

KM-797-7N

KM-797BL

KM-797BL-7S

KM-797BL-7N

General to heavy material

3,000 SPM

5 mm

13 mm

5 # 14 (#11 ~ #22)

1.6mm ~ 52.4mm

16mm ~ 50.8 mm

1.6mm ~ 38mm

5 #22 (#11 ~ #22)

13 mm

7 mm

33.4 mm

1 mm

7 mm

15 mm

Automatic lubrication

Usage

Max sewing speed

Max no. of stitches

Needle bar stroke

Feed dog height

Manual

Knee

Automatic

Needle

Lubrication

Needle width gauge

Presser

foot height

Model Name

Item

KM-797BL-7N

KM-797BL-7S

KM-797BL

KM-797-7N

KM-797-7S

KM-797

General to heavy material

3,000 SPM

5 mm

13 mm

5 # 14 (#11 ~ #22)

2.4mm ~ 15.9mm

5 #22 (#11 ~ #22)

13 mm

7 mm

33.4 mm

1 mm

7 mm

15 mm

Automatic lubrication

Specification

High-speed, two needle, drop feed, needle feed, standard hook sewing machine

High-speed, two needle, drop feed, needle feed, standard hook sewing machine with automatic thread trimmer (Servo motor)

High-speed, two needle, drop feed, needle feed, standard hook sewing machine with automatic thread trimmer (470 motor)

High-speed, two needle, drop feed, needle feed, double hook sewing machine

High-speed, two needle, drop feed, needle feed, double hook sewing machine with automatic thread trimmer (Servo motor)

High-speed, two needle, drop feed, needle feed, double hook sewing machine with automatic thread trimmer (470 motor)

High-speed, two needle each, drop feed, needle feed, standard hook sewing machine

High-speed, two needle each, drop feed, needle feed, standard hook sewing machine with automatic thread trimmer (Servo motor)

High-speed, two needle each, drop feed, needle feed, standard hook sewing machine with automatic thread trimmer (470 motor)

High-speed, two needle each, drop feed, needle feed, double hook sewing machine

High-speed, two needle each, drop feed, needle feed, double hook sewing machine with automatic thread trimmer (Servo motor)

High-speed, two needle each, drop feed, needle feed, double hook sewing machine with automatic thread trimmer (470 motor)

Summary of Contents for KM-757




































Search results

Summary of Contents for KM-757

Reviews:

Related manuals for KM-757

Brands by name

Popular brands

SunStar KM-757, User Manual

Search results

Summary of Contents for KM-757

Reviews:

Related manuals for KM-757

Brands by name

Popular brands