Suntor ST30HPT User Manual Download

Page: 1 / 16

1st

ST30HPT User Manual

TX on Board

RX on Ground

Contents

...............................................................................................................................................................................2nd

II. Precautions for integration

...................................................................................................................................................2nd

III. List of in-box items

................................................................................................................................................................3rd

IV. Interface Definition

............................................................................................................................................................... 5th

1. TX Interface Definition

...................................................................................................................................................5th

2. RX Interface Definition

...................................................................................................................................................6th

V. Operating Instructions & Steps

..............................................................................................................................................7th

VI. Antenna Installation

............................................................................................................................................................. 9th

1. Multi-rotor UAV

............................................................................................................................................................. 9th

2. Fixed Wing UAV

..............................................................................................................................................................9th

VII. Software Operation

........................................................................................................................................................... 10th

7.1. Two ways for changing the parameters

................................................................................................................... 10th

7.2. How to use the software

.......................................................................................................................................... 11th

7.2.1. Login

...............................................................................................................................................................11th

7.2.2. RF Configuration

............................................................................................................................................12th

7.2.3. RS1 Configuration

.......................................................................................................................................... 14th

7.2.4. RS2 Configuration

.......................................................................................................................................... 15th

7.2.5. IP New Network Configuration

......................................................................................................................15th

7.2.6. RF New NET Configuration

.................................................................................................................................... 16th

SUNTOR ELECTRONICS CO., LIMITED

V2.0

Summary of Contents for ST30HPT

















Search results

Summary of Contents for ST30HPT

Reviews:

Related manuals for ST30HPT

Brands by name

Popular brands

Suntor ST30HPT, User Manual

Search results

Summary of Contents for ST30HPT

Reviews:

Related manuals for ST30HPT

Brands by name

Popular brands