Synway Information Engineering Co., Ltd
SMG Series Analog Gateway User Manual (Version 1.5.3)
Page 9
in again.
Step 8: Modify IP address of the gateway.
You can modify the IP address of the gateway via ‘System Tools
Æ
Network’ on the WEB interface
to put it within your company’s LAN. Refer to
for detailed instructions about IP
modification. After changing the IP address, you shall log in the gateway again using your new IP
address.
Step 9: Make phone calls.
Note: For your easy understanding and manipulation, all examples given in this step do not
involve registration, that is, SIP initiates calls in a point-to-point mode.
Situation 1: Call from a station to another (Tel
Æ
Tel)
The gateway allows two FXS ports to call each other by default. Just use a station connected with
an FXS port to dial the number of the destination FXS port and you can make a Tel
Æ
Tel call. The
default number of an FXS port is 80XX, among which XX represents the corresponding port
number. For example, the default number corresponding to Port 1 is 8001, and that corresponding
to Port 32 is 8032.
Actually a Tel
Æ
Tel call on the gateway is accomplished via the routing of Tel
Æ
IP
Æ
IP
Æ
Tel. For
detailed introductions and configuration guide, refer to
in Appendix B.
Situation 2: Call from a station to an IP phone (Tel
Æ
IP)
1. Go to ‘Advanced Settings
Æ
Dialing Rule’ on the WEB interface and click the ‘Add New’
button to add a new dialing rule. Refer to
for detailed instructions. Enter
either a particular number or a string of ‘x’s to represent several random numbers. For
example, ‘xxx’ denotes 3 random numbers. You may use the default value of ‘Index’ and are
required not to leave ‘Description’ empty.
Example:
Set
Index
to
99
, fill in
Description
with
test
and configure
Dial Rule
to
123
.
2. Go to ‘Port Settings
Æ
Port Group’ on the WEB interface and click the ‘Add New’ button to
create a new port group and add FXS ports which are connected with stations to it. Refer to
for detailed instructions. You may use the default values of other
configuration items and are required not to leave ‘Description’ empty.
Example:
Provided the FXS port which is connected with a station is Port1, check the
checkbox before
Port1
, set
Index
to
1
, fill in
Description
with
test
, and keep the default
values of other configuration items.
3. Go to ‘Route Settings
Æ
Tel
Æ
IP’ on the WEB interface and click the ‘Add New’ button to add
a new routing rule. Refer to
for detailed instructions. Select the port group
created in Step2 as ‘Source Port Group’ and fill in ‘Destination IP’ and ‘Destination Port’ with
the IP address and the Port number you plan to call. You may use the default values of other
configuration items and are required not to leave ‘Description’ empty.
Example:
Provided the remote IP address intended to call is 192.168.0.111 and the port is
5060. Set
Index
to
63
,
Source Port Group
to
1
, fill in
Description
with
test
, configure
Destination IP
to
192.168.0.111
,
Destination Port
to
5060
, and keep the default values of
other configuration items.
4. Pick up the station and dial the number set in Step1 to ring the remote IP phone. If you have
set a particular number in Step 1, only this number you can dial; if you have set a string of ‘x’s,
how many ‘x’s there are, how many random numbers you can dial.
Example:
Pick up the station and dial 123. Then the IP phone with the IP address
192.168.0.111 and the port 5060 will ring.
Situation 3: Call from an IP phone to a station (IP
Æ
Tel)
1. Go to ‘Port Settings
Æ
Port Group’ on the WEB interface and click the ‘Add New’ button to
create a new port group and add FXS ports which are connected with stations to it. Refer to
