SUPATRAC Blackbird Instructions & Warranty Download

Page: 12 / 12

supatrac.com

DISASSEMBLY

To disassemble, reverse the installation.

1. Protect your stylus with a guard.

2. Gently lift the arm to raise it and use the

tweezers to feed the left and right hoist
toggles through the hoist holes in the
thrust box, being careful not to tug the
electrical connections destructively.

3. Use the tweezers to unplug the electrical

contacts by gripping the plugs with
tweezers, not the wires, and gently pull
them upwards until they detach.

4. The arm is now detached and can be

stored somewhere safe.

5. Unplug the arm cable from the bottom of

the pillar.

6. Loosen the pillar locking bolt, taking care

not to allow the pillar to drop, and remove
the pillar.

7. Unbolt the base.

FURTHER INFORMATION

For further information, please visit
www.supatrac.com
or email info@supatrac.com

SUPATRAC tone-arms are designed and
made by hand in Chelsea, London, England.

Summary of Contents for Blackbird













Search results

Summary of Contents for Blackbird

Reviews:

Related manuals for Blackbird

Brands by name

Popular brands

SUPATRAC Blackbird, Instructions & Warranty

Search results

Summary of Contents for Blackbird

Reviews:

Related manuals for Blackbird

Brands by name

Popular brands