background image

32

Absorption phase

In this phase the charge voltage must be maintained at UAbsorption to fully charge the 
battery. If the charger currents drop below 5% (Imin) of the 1C current the absorption phase 
can be maintained for t2 minutes, see Table 16.

Absorption Phase

Parameter

Typical

Min

Max

Remark

U

Absorption 

14,6V DC 

14,2V DC 

14,8V DC

-

I

min 

3% of 1C 

5% of 1C

-

t

20 minutes 

10 minutes 

1 hour

-

t

10 minutes 

5 minutes 

30 minutes 

-

Table 17.  Absorption Phase

Float phase

In this phase the charge voltage is set to UFloat. If the battery voltage drops below UReturn 
for longer than t4 seconds than the charging process has to be repeated.

Float Phase

Parameter

Typical

Min

Max

Remark

U

Float

13,5V DC

13,4V DC

13,6V DC

-

t

4

60 sec

5 sec

120 sec

-

Table 18. Float Phase

Optional maintenance phase

If supported by the charger, every t3 hours the charger can do a maintenance charge to 
make sure that the batteries are kept fully charged.

Maintenance Phase

Parameter

Typical

Min

Max

Remark

t

3

720 hours

168 hours

4320 hours

-

Table 19. Maintenance phase

Summary of Contents for Epsilon SB12V1200Wh-M



















































Reviews: