background image

1-6

 PDSMi

 

User’s Manual

Motherboard Features 

CPU 

 

Latest CPU technology! 

•   Single Intel Pentium D (Dual-Core)/Pentium 4 Extreme Edition/Pentium 4/Pen-

tium Extreme Edition/Celeron D LGA (Land Grid Array) 775 Processors at system 

bus speeds of 1066 MHz/800 MHz/533 MHz.   

•   Hyper-Threading (HT), EM64T, Enhanced Intel SpeedStep (EIST) supported

Using the EM64T Feature

•  Install a 64-bit OS (Windows XP Professional x64 Ed, Server 2003x64 Ed.)

•  Install the 64-bit drivers for all MB components, devices and add-on cards

Using the Hyper-Threading (HT) Technology

•  Use a CPU that supports Hyper-Threading Technology

•  Install an OS that supports HT, including Windows XP/2003 Server and Linux 

2.4x. (Under  Linux, use the HT compiler to compile the code. For other oper-

ating systems, be sure to disable the HT feature in the BIOS.)

•  Enable the HT feature in the BIOS (under "Advanced" Setting) before install-

ing a supported OS. (*Note: visit www.Intel.com for CPU support and driver 

updates.)

• 

OS Licensing Support 

•  Intel Dual-Core CPU supports: Windows 2000 Professional,  Windows 

Advanced Server, Windows XP Home, Windows XP Professional, Windows 

Server 2003 (Standard, Enterprise)

•   Intel Dual-Core CPU and Hyper-Threading Technology supports: Windows 

2000 Advanced Server, Windows XP Home, Windows XP Professional, Windows 

Server 2003 (Standard, Enterprise) 

Memory

 

 

Latest memory technology! 

 (*

Note: See Section 2-4 for details.) 

 

•  Four DIMM slots support Dual/Single Channel DDRII 667/533/400 MHz up 

to 8 GB of  ECC Unbuffered two-way interleaved DDRII SDRAM.

Chipset

 

 Latest Intel chipset technology!

• Intel 

 

E7230 

(Mukilteo) 

• Intel 

ICH7R

• Intel 

PXH

Expansion Slots

•  One (1) PCI 32-Bit/33 MHz (Slot 1)

•  One (1) PCI-X 64-Bit 133 MHz slot (Slot 6) + (1) PCI-E x8 (Signal: x8 via 

Riser Card) (Slot SXB-E1)

 

BIOS

 

•  8Mb Firmware Hub Phoenix BIOS

 

 

 

•  APM 1.2, DMI 2.3, PCI 2.2, PCI-X 1.0,ACPI 1.0, Plug and Play (PnP), SM-

BIOS 2.3, Hardware BIOS Virus Protection

Summary of Contents for PDSMi





































































































Reviews: