background image

3. Technical Features

The refrigerator is a ventilated system, the evaporator is in a separate insulated box on the top. 
All the materials used in the manufacturing of this unit are guaranteed to be suitable for use 
with perishable foods. The gases used in the refrigerators are R-134a; in the refrigerator for 
frozen food maintenance is R-404a. 

The refrigerating circuit is in compliance with the current normative. 

4. Operation

The gas in the refrigerating circuit is 

first 

compressed, liquefied and then evaporated in the 

ventilated evaporator, situated on the top of the container. 

This cycle involves the absorption of heat from the air in the refrigerator compartment and is

 

then

 cooled. The heat produced is then dissipated to the outside environment by a condenser 

unit located on the top of the refrigerator. 

5. Control Unit

The refrigerator 

responds to

 command

from a "digital control unit" and a "main switch pilot 

light" in the top panel of the refrigerator. 

The "main switch pilot light" is for turning on the power supply. 

The red pilot light comes on to indicate that the unit is connected to the main electricity and to 
start work. 

The red pilot light comes off to indicate that the unit is disconnected and do

esn't

 work. The 

"digital control unit" is for the regulation of all parameters to provide the correct working of the 
refrigerator. Please consult all parameters in the attachment manual of the "digital control 
unit". 

This manual is part of the instruction manual and is very important in case of service. 

Applied refrigerant belong

s

 to non-flammable refrigerant. 

4

©Supera

V.1.0 | October 2014

Summary of Contents for G1R-1













Reviews: