background image

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes 

no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update 

or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: 

For the most up-to-date version of this manual, please see our website at 

www.supermicro.com

.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual 

at any time and without notice. This product, including software and documentation, is the property of Supermicro and/

or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except 

as expressly permitted by the terms of said license.

IN  NO  EVENT  WILL  Super  Micro  Computer,  Inc.  BE  LIABLE  FOR  DIRECT,  INDIRECT,  SPECIAL,  INCIDENTAL, 

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT 

OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER 

MICRO COMPUTER, INC. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED 

OR  USED  WITH  THE  PRODUCT,  INCLUDING  THE  COSTS  OF  REPAIRING,  REPLACING,  INTEGRATING, 

INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the 

State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution 

of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product. 

FCC Statement: This equipment has been tested and found to comply with the limits for a Class A or Class B digital 

device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against 

harmful interference when the equipment is operated in industrial environment for Class A device or in residential 

environment for Class B device. This equipment generates, uses, and can radiate radio frequency energy and, if not 

installed and used in accordance with the manufacturer’s instruction manual, may cause harmful interference with 

radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in 

which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only 

to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. 

See 

www.dtsc.ca.gov/hazardouswaste/perchlorate

”.

 

 

 

 

 

 

WARNING: This product can expose you to chemicals including 
lead, known to the State of California to cause cancer and birth 
defects or other reproductive harm. For more information, go 
to www.P65Warnings.ca.gov. 

 

The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, 

nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical 

systems whose failure to perform be reasonably expected to result in significant injury or loss of life or catastrophic 

property damage. Accordingly, Supermicro disclaims any and all liability, and should buyer use or sell such products 

for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully 

indemnify, defend and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and 

proceedings of any kind arising out of or related to such ultra-hazardous use or sale.

Manual Revision 1.0

Release Date: August 11, 2021

 

Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this 

document. Information in this document is subject to change without notice. Other products and companies referred 

to herein are trademarks or registered trademarks of their respective companies or mark holders.

Copyright © 2021 by Super Micro Computer, Inc.

 

All rights reserved. 

Printed in the United States of America

Summary of Contents for CSE-LB16-AW






















































Reviews: