background image

Chapter 7: BIOS

7-5

at bootup and allow the drives that are attached to these host adaptors to function 

as bootable disks. If this item is set to Disabled, the ROM BIOS of the host adap-

tors will not capture Interrupt 19, and the drives attached to these adaptors will not 

function as bootable devices. The options are 

Enabled

 and Disabled. 

Power Confi guration

Watch Dog Function

If enabled, the Watch Dog timer will allow the system to automatically reboot when 

a non-recoverable error occurs that lasts for more than fi ve minutes. The options 

are Enabled and 

Disabled.

Power Button Function

If this feature is set to Instant Off, the system will power off immediately as soon 

as the user presses the power button. If this feature is set to 4 Seconds Override, 

the system will power off when the user presses the power button for 4 seconds or 

longer. The options are 

Instant Off

 and 4 Seconds Override.

Restore on AC Power Loss

Use this feature to set the power state after a power outage. Select Stay Off for the 

system power to remain off after a power loss. Select Power On  for the system 

power to be turned on after a power loss. Select Last State to allow the system 

to resume its last state before a power loss. The options are Stay Off,

 

Power On, 

and 

Last State

.

X

CPU Confi guration

This submenu displays the information of the CPU as detected by the BIOS. It also 

allows the user to confi gure CPU settings.

X

Socket 1 CPU Information/Socket 2 CPU Information

This submenu displays the following information regarding the CPUs installed 

in Socket 1/ Socket 2.

• 

Type of CPU

• 

CPU Signature

• 

Microcode Patch

• 

CPU Stepping

• 

Maximum / Minimum CPU Speed

Summary of Contents for 6047R-E1R24L




















































































































Reviews: