background image

       

AOC-SAT2-MV8 User's Guide

4

1. Introduction

T h i s   m a n u a l   i s   w r i t t e n   f o r   s y s t e m   i n t e g r a t o r s ,   P C   t e c h n i c i a n s   a n d

knowledgeable PC users who intend to integrate Supermicro's SAT2-MV8

SATA Controller into their system.  It provides detailed information for the

installation and use of the SAT2-MV8 card. The Supermicro SAT2-MV8 of-

fers an innovative, complete and cost effective solution to the ever-increas-

ing demands of disk density and data integrity of today's servers.

1.1 Overview

The SAT2-MV8 is a highly efficient, highly compatible and easy-to-use SATA

RAID Controller that allows the user to configure RAID functions by using

Marvell's 88SX6081 8-port Serial ATA  Host Controller, offering 64-bit PCI-X

bus interface with high performance features.  With the SATA physical

interface support at 1.5 and 3.0 Gbps, the SAT2-MV8  is a high speed, high

bandwidth RAID Controller that can integrate multiple high capacity drives to

provide the user with maximum storage space.

Product Features

Low profile Form Factor (w/ the PCB size of 2.5" H x 6.4" W)

Marvell's 88SX6081 8-port Serial ATA Host Controller

Eight SATA ports @ 1.5 or 3.0 Gigabits per second (Gbps)

64-bit, 133 MHz PCI-X bus

Flash BIOS Interface

Presence LED Indicator and Activity Indicator for each port

Software RAID 0, RAID 1, RAID 10 and JBOD (-simple volume) supported
(*Note: Some operating systems might not support Software RAID.)

Bootability from a single drive.

Operating Systems supported

• Windows 2000, 

XP, 

 

2003, XP EM64T, 2003 EM64T

•  

Linux: (-source code provided)--the driver disks currently available:

•  

RedHat 9 (2.4.20-6 and 2.4.20-8)

•  

RedHat Enterprise Linux 3 Update 2, Update 3, and Update 4.

•  

RedHat Enterprise Linux 3 EM64T/X86_64 Update 3 and Update 4.

•  

RedHat Enterprise Linux 4 and RedHat Enterprise Linux 4 EM64T/X86_64.

•  

SuSE 9.1, 9.2 and SuSE Linux Enterprise Server 9.

•  

Fedora Core 3.

An Important Note  to the User

All images and layouts shown in this user's guide were based upon

the latest revision available at the time of publishing. The card you've

received may or may not look exactly the same as the ones shown in

this manual.

Summary of Contents for AOC-SAT2-MV8



















Reviews: