background image

    SC812/SC812L Chassis User's Guide

1-2

Table of Contents

Chapter I: Introduction ............................................................... 1-3

A. Front Panel Connectors ............................................................................ 1-3

B. Front Panel LED Indicators ....................................................................... 1-3

C. Front Panel LED Descriptions .................................................................. 1-3

D. Back Panel Connectors ............................................................................. 1-4

E. An Important Note to the User ................................................................. 1-4

Chapter 2: Installation Procedures ........................................... 2-1

Section 1: Installing components into the Chassis .................... 2-1

A. Removing the Top Cover from the SC812/SC812L Chassis .............. 2-1

B-1. Removing and Installing the Disk Drive ............................................... 2-2

B-2. Removing and Installing the Hard Drive Disks ................................... 2-3

C-1. Rail Installation .......................................................................................  2-4

C-2. Installing Chassis Rails .........................................................................  2-5

D-1. Rack Installation for the Traditional 1U Design ................................. 2-7

D-2. Rack Installation for the Open-Rack Design ...................................... 2-9

Section 2: SCSI (Super) GEM Driver Installation Instructions for the
Windows OS ...................................................................................... 2-12

User's Guide Revision: Revision 1.0

Release Date: July 28, 2006

Summary of Contents for SC812 Series

















Reviews: