SC825 Chassis Manual
D-6
D-7
Appendix D: BPN-SAS3-825TQ Backplane Specifications
D-6 Rear Jumpers
Figure D-3. Jumpers
1
1
16
32
48
BAR CODE
REV 2.0
SAS825TQ
1
GND
GND
+12V
+5V
GND
GND
+12V
+5V
#2
I C
#1
ACT_IN
JP29:9072 RESET
I C
SIDEBAND #2
SIDEBAND #1
2
2
+ +
+ +
+ +
+ +
+
+
+
+
+
+
1
1
1
16
32
48
GND
GND
+12V
+5V
GND
GND
+12V
+5V
+
+
+
BAR CODE
+
+
+
REV 2.0
SAS825TQ
#2
2
I C
#1
ACT_IN
JP29:9072 RESET
2
I C
SIDEBAND #2
SIDEBAND #1
+ +
+ +
+ +
+ +
JP18
JP29
JP50
JP37
JP38
JP34
JP36
JP43
JP33
JP42
JP41
JP40
Jumper Settings
Jumper
Jumper Settings
Note
JP29
Open (Jumper off the pins): Default
Closed (Jumper on the pins): Reset
MG9072 chip reset
JP18
Not used
SGPIO and I
2
C Modes and Jumper Settings
This backplane can utilize SGPIO or I
2
C. SGPIO is the default mode and can be
used without making changes to your jumpers. The following tables describe jumper
settings for each mode.
SGPIO Settings (Default)
Jumper
Jumper Setting
Notes
JP33
1-2
Controller ID #1
JP34
1-2
Backplane ID #1
1-2: ID#0
JP36
1-2
Controller ID #2
JP37
1-2
Backplane ID #2
1-2: ID#0
JP38
Open (Jumper off the pins)
I
2
C Reset #2
JP40
Closed (Jumper on the pins)
I
2
C Reset_SDOUT#1
JP41
Closed (Jumper on the pins)
I
2
C Reset_SDOUT#2
JP42
1-2
I
2
C Backplane ID_SDIN#1
JP43
1-2
I
2
C Backplane ID_SDIN#2
JP50
Open (Jumper off the pins)
I
2
C Reset #1
I
2
C Settings
Jumper
Jumper Setting
Notes
JP33
2-3
Controller ID #1
JP34
1-2
Backplane ID #1
1-2: ID#0
2-3: ID#1
JP36
2-3
Controller ID #2
JP37
2-3
Backplane ID #2
1-2: ID#0
2-3: ID#1
JP38
Closed (Jumper on the pins)
I
2
C Reset #2
JP40
Open (Jumper off the pins)
I
2
C Reset_SDOUT#1
JP41
Open (Jumper off the pins)
I
2
C Reset_SDOUT#2
JP42
2-3
I
2
C Backplane ID_SDIN#1
JP43
2-3
I
2
C Backplane ID_SDIN#2
JP50
Closed (Jumper on the pins)
I
2
C Reset #1
Explanation of Jumpers
To modify the operation of the backplane,
jumpers can be used to choose between
optional settings. Jumpers create shorts
between two pins to change the function
of the connector. Pin 1 is identified with
a square solder pad on the printed
circuit board.
Note
: On two pin jumpers,
"Closed" means the jumper is on and
"Open" means the jumper is off the pins.
Connector
Pins
Jumper
Setting
3 2 1
3 2 1
Summary of Contents for SC825TQ-560LP
