13.PLAY/PAUSE BUTTON
16.STOP BUTTON
Radio
reception
1
.
Press function button select
RADIO
mode
.
2
.
Press BAND to select the desired wave band:AM,FM,FM ST.
3.Tune to required station by Rotate BACK
/
NEXT or press PRE
-
DN
/
PRE
-
UP.
Manual tuning: Rotate BACK or
NEXT and then release within 1 sec.
Auto tuning:
Press the play/pause button enter the automatic channel
scan mode, and to be put automatically sets.
Preset channel
:(
FM
30 Preset memories,AM 10 preset memories
)
(1)Rotate BACK
/
NEXT Select desired station.
(2) Press PROGRAM button once , The MEMORY number indicator begins steady in the
display.
(3) Press PRESET-UP OR PRESET- DN buttons to select the desired number.
(4) Press PROGRAM button to save that station.
(5) Repeat steps (1) to (4) procedures for other stations.
4.After end of program. press PRE-UP or PRE-DN to start play the frequency that you selected or
Press number key on the remote control.
5.Rotate
[VOL-]or [VOL +] to adjust the volume.
6.Extend TELESCOPIC ANTENNA to its full length if you are listening to FM broadcasting.
7.Turn off the radio by press FUNCTION button select other mode
or
press
power
button
to
off
the
unit.
8.Switch
on
again
after
shut
down
,
the
memory
frequency
still
exists
.
MONO/STEREO
-Press MO/ST button once,to mono state
.
-Press MO/ST button twice, to stereo state,stereo is displayed
.
Remote Control
EN-5
EN-4
,
,
,
,
,
,
,
,
Using AC Power
1.check if the power voltage, as shown on the type plate located on the bottom of the set,
corresponds to your local ac power supply. if it does not, consult your dealer or service centre .
2.connect the power cord to the ac mains inlet and the wall outlet. the power supply is
now connected and ready for use.
3.to switch off completely, unplug the power cord from the wall outlet.
unplug the power cord from the wall outlet to protect your set during heavy thunderstorms.
Batteries (not included)
Open the battery compartment and insert
eight batteries,
(preferably Alkaline) with the correct polarity
as indicated by the + and - symbols
inside the compartment.
Batteries contains chemical substances, so
they should be disposed of properly
Incorrect use of batteries can cause electrolyt
leakage and will corrode the compartment or
cause the batteries to burst. Therefore:
Do not mix battery types: e.g. alkaline with carbon Zinc. Only use batteries of the same
type for the set.
When inserting new batteries, do not try to mix old batteries with new ones.
Remove the batteries if the set is not be used for a long time.
type R-20, UM-1 or D-cells,
POWER SUPPLY
BASIC FUNCTION
USE
CLOCK
to
setup
the
time
of
the
unit
1
.
connect
the
ac
on
(
.
2
.
short according to the time button
,
the
time
will
flashing
on
the
lcd
display
.
3
.
press
BACK
、
NEXT
to
select
the
number
of
the
time
.
you
can
setup
the
time
format
by
12h
or
24h
.
4
.
press
time
button
to
confirm
.
5
.
then
you
can
set
the
hour
and
the
minute
with
the
same
method
of
steps
3
-
4
.
6
.
with
the
same
method
of
steps
3
-
4
.
The following operation must be in standby mode)
after setup the unit time, long press the time button can setup the unit begin working time ,
Note: after setup the beginning time, the lcd will display the radio/cd/usb/sd/tape/aux/ipod mode,
Press the BACK or NEXT to choose the mode, then it press time button to affirm, otherwise it play
usb or aux mode first.
