background image

INTRODUCTION

INTRODUCTION

Please read and understand this owner’s manual before installing your H9Wwinch. Your H9W winch is a very powerful machine. If used unsafely
or improperly, there is a possibility that property damage or personal injury can result. We have included several unique features in the winch to
minimise this possibility; however, your safety ultimately depends on your caution when using the product.

Correct installation of your H9W winch is a requirement for proper operation.

Please note:

The Superwinch H9W winch is designed for total reliability during vehicle recovery operations. This winch is not designed to be
used in hoisting applications and Superwinch does not warrant it suitable for such use.

Superwinch reserve the right to alter model specifications without prior notice. 

PLEASE KEEP THIS OWNER’S HANDBOOK WITH THE WINCH.

Pay particular attention to the caution noted preceded with the symbols shown here. The notes contain advice for your protection.

WARNINGS, CAUTIONS AND NOTES

These are given through these instructions in the following form :

WARNING : Procedures which must be followed precisely in order to avoid the possibility of personal injury.

CAUTION : This calls attention to procedures which must be followed to avoid damage to components.

NOTE : This calls attention to methods which make a job easier or gives helpful information.

USAGE OF WINCH

This winch is designed for use in applications such as:

Pulling
Hauling
Lifting (Vehicle Recovery ONLY)
and other associated uses.

POISONOUS SUBSTANCES

Many liquids  and  other substances used should  under  no  circumstances  be  consumed,  and  should  be kept  away  from  open  wounds. These
substances include (among others) hydraulic oil.

SYNTHETIC RUBBER

Many ‘O’ ring seals, flexible pipes and similar items, when subjected to fire or heat can become highly corrosive. Handle with seamless industrial
gloves only. Should skin contact occur, remove contaminated clothing immediately and obtain medical assistance without delay. Meanwhile, wash
the affected area with copious amounts of cold water or limewater for 15 to 60 minutes.

RECYCLING AND THE ENVIRONMENT

It is illegal to dispose of used oil in the ground, down sewers or drains or into waterways.

Dispose of used oil through authorised waste disposal contractors. If in doubt contact your local Authority for advice on disposal facilities.

01

INTRODUCTION

01-1

SUPERWINCH winches are not to be used to lift, support or otherwise transport personnel.

Any such use shall be considered to invalidate the warranty and Superwinch shall not

be responsible for any claims arising from such use.

Summary of Contents for 8569














Reviews: