background image

7.  ERROR CODES

Electronic control fault table

DISPLAY FAILURE DESCRIPTION

REASON

SOLUTION

Non

Standby

Non

Normal boot

P01

Inlet Temp. Sensor Fault

The temp. Sensor is broken or 
short circuit

Check or change the temp. 
Sensor

P02

Outlet Temp.Sensor Fault

The temp. Sensor is broken or 
short circuit

Check or change the temp. 
Sensor

P04

Coil Temp.Sensor Fault

The temp. Sensor is broken or 
short circuit

Check or change the temp. 
Sensor

P05

Amibent Temp.Sensor Fault

The temp. Sensor is broken or 
short circuit

Check or change the temp. 
Sensor

P07

Suction Temp.Sensor Fault

The temp. Sensor is broken or 
short circuit

Check or change the temp. 
Sensor

P081

Discharge Temp. Sensor Fault

The temp. Sensor is broken or 
short circuit

Check or change the temp. 
Sensor

E01

High Pressure Prot.

The high-pressure switch is 
broken

Check the pressure switch and 
cold circuit

E02

Low Pressure Prot.

Low pressure1 protection

Check the pressure switch and 
cold circuit

E03

Flow Switch Prot.

No water/little water in water 
system

Check the pipe water flow and 

water pump

E07

Anti-freezing Prot

Water flow is not enough

Check the pipe water flow 

and whether water system is 
jammed or not

E19

Primary Anti-freezing Prot.

The ambient temp. is low

E29

Secondary Anti-freezing Prot.

The ambient temp. is low

E06

Inlet and outlet temp. too big

Water flow is not enough and 

low differential pressure

Check the pipe water flow 

and whether water system is 
jammed or not

Non

Low temperature protection

The environmental temp. is low

E051

Comp. Overcurrent Prot.

The compressor is overload

Check whether the system 
of the compressor running 
normally

P082

Exhaust Air over Temp Prot.

The compressor is overload

Check whether the system 
of the compressor running 
normally

Heatseeker NovaS Heat Pump 

Installation & User Manual

23

Summary of Contents for Heatseeker NovaS













































Reviews: