background image

LIMITED WARRANTY

Sure Heat Mfg warrants that the components of this appliance are warranted free from defects 

in material and workmanship for one year from the date of purchase. Sure Heat Mfg. at its 

option, will repair or replace this product or any component of the product found to be defective 

during the warranty period. Replacement will be made with a new manufactured product or 

component. if the product is no longer available, replacement may be made with a similar 

product of equal value. This warranty does not include transportation or shipping costs of any 

kind. This is your exclusive warranty.

This warranty is valid for the original retail purchaser from the date of initial retail purchase 

and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain 

warranty parts.

This warranty does not cover normal wear of parts such as scratches and dents of the  

components or damage resulting from any of the following:

negligent use or misuse of the product, including exposing the product to chemicals or cleaning products not 

approved by Sure Heat Mfg.
corrosion, rust or discoloring of any kind.
use or installation contrary to specified instructions and applicable building codes, including heating the product 

to temperatures above its rated specifications which can cause considerable warping
disassembly, including removal of the product from a built-in installation
damage resulting from accident, alteration, misuse, abuse, hostile environments, or improper installation
repair or alteration
acts of God, such as fire, flood hurricanes, and tornadoes
gas cylinders, propane tanks or other fuel delivery systems, including connections to a household fuel supply
usage other than single-family household use such as commercial or industrial use
minor warping or discoloration of parts, which is normal and not a defect under this warranty

DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE

If the appliance does not operate properly, first thoroughly carry out the instructions provided 

with the unit to ensure that the appliance is installed correctly and check the troubleshooting 

section in the use and care manual.

We recommend you return the warranty registration card so that you can be contacted with any 

questions of safety arise that could affect you. The return of the warranty registration card is 

not a condition for warranty coverage.

Because of continuing product improvement these specifications are subject to change without 

notice.

If you have other questions or need replacement parts contact our

Customer Service Hotline at (800) 229-5647 or

visit our website at www.sureheat.com

Sure Heat Manufacturing 1861 West Oak Parkway Marietta, GA 30062



21

Summary of Contents for Four Seasons FS87PHLP






















Reviews: