background image

SureCall  |  48346 Milmont Drive, Fremont CA 94538  |  1-888-365-6283  |  support@surecall.com

SureCall  |  48346 Milmont Drive, Fremont CA 94538  |  1-888-365-6283  |  support@surecall.com

5

4

Introduction & Overview

CHAPTER 1: INTRODUCTION & OVERVIEW

1.1 Product Overview

SureCall’s Guardian2 QR is a bi-directional communications amplifier for police headquarters, fire stations, hospitals, 
and other first-responder facilities. The BDA services the full public safety 700MHz and 800MHz bands.
The Guardian2 QR significantly improves the quality of crucial first-responder communications in buildings with weak 
signal strength. For optimal coverage, the BDA uses built-in safeguards to eliminate interference to public-safety 
networks. It meets NEMA 4 type requirements, and is upgradable in the field. Plus, the Guardian2 QR offers the 
industry’s best three-year warranty available.
The Guardian2 QR is enclosed in a NEMA-4 compatible housing, and enhances the coverage area of first responder 
radio communications for in-building applications. It is equipped with bi-directional paths (down-link & up-link) for 
transmit and receive frequencies, and advanced filtering technology for low-noise amplification of signals.

1.2 Package Contents

Your BDA box contains the following items:
•  Guardian2 bi-directional amplifier
•  NEMA-4 rated housing
•  AC power cable
•  DC power cable and connector
•  Alarm cable and connector
•  Ethernet connector
•  Mounting kit 

1.3 Additional Items Needed

The Guardian2 QR needs the following additional components for a complete install:
•  External antenna
•  Lightning protector
•  Cable splitter if installing multiple antennas
•  Sufficient SC-400 ultra-low loss interior/exterior cable, 50 ohm
•  Multiple antennas (omnidirectional domes and/or panels by SureCall)
•  Grounded surge suppressor for DC power supply

1.4 Key Features & Benefits

•  Suitable for large coverage areas.
•  Extends signals in areas with poor coverage due to geographical location and/or building design.
•  Powerful in-building BDA with 31dB of adjustable gain level.
•  NEMA-4 rated amplifier housing. No additional NEMA enclosure required.
•  Integrated 7-pin alarm and UPS port for external battery backup.
•  Power control maintains maximum output power at 26 dBM.

•  Automatic oscillation detection and protection system powers down the BDA to prevent harmful radio 

interference.

•  Automatic gain control (AGC).
•  Features built-in SureCall Sentry remote-monitoring system with Ethernet port.

1.5 Optional Accessories

SureCall provides many optional features and accessories for the Guardian2 QR Amplifier. See table below:

Splitters and Couplers

SC-WS-2

Wide Band 2 Way Splitter

SC-WS-3

Wide Band 3 Way Splitter

SC-WS-4

Wide Band 4 Way Splitter

SC-C-6

-6dB Coupler

SC-C-10

-10dB Coupler

Outdoor Antenna Options

SC-288W

Wide Band Omni-directional 50 ohm Fiberglass Antenna 3 to 4dBi (includes mounting kit, 698-2700 MHz)

SC-230W

Wide Band Yagi Directional 50 ohm Antenna 10 to 11dBi gain (includes mounting kit, 698-960 & 1710-2700 MHz)

Inside Antenna Options

SC-222W

Wide Band Dome 50 ohm Antenna - 3 to 4dBi (includes mounting kit, 698 -2700 MHz)

SC-248W

Wide Band Panel 50 ohm Antenna - 7 to 10dBi (includes mounting kit,  698-2700 MHz)

Plenum Cable

SC-PL-30FT

30' SC400 Ultra Low Loss Coax Plenum Fire Rated Cable with N-Male connectors - Orange

SC-PL-75FT

75' SC400 Ultra Low Loss Coax Plenum Fire Rated Cable with N-Male connectors - Orange

SC-PL-1000FT

1000' SC400 Ultra Low Loss Coax Plenum Fire Rated Cable - Orange

Ultra Low Loss Cable
SC-006-1000

1,000' SC600 Ultra Low Loss Coax Cable. Connectors not included - Black

Accessories & Connectors

SC-LP

Lightning Protector

SC-ATNR-5

5 dB RF Attenuator

SC-ATNR-10

10 dB RF Attenuator

SC-ATNR-20

20 dB RF Attenuator

SC-CN-09

N Male Crimp Connector, 400 and Plenum Cable

SC-CN-12

N Male to N Male Connector

SC-CN-16

N Male Connector, 600 Cable

SC-Mount-Pole

L Bracket mount with U bolt hardware for donor antenna mount to J-bar

SC-Mount-JBar

Steel 1 inch J-Bar mount for donor antenna.  Antenna mount not included  

Introduction & Overview

Summary of Contents for Guardian2 QR
























Reviews: