20731L / 20741L
BEDIENUNGSANLEITUNG / INSTRUCTION MANUAL
www.swstahl.de
SW-Stahl GmbH
Tel. +49 (0) 2191 / 46438-0
An der Hasenjagd 3
Fax +49 (0) 2191 / 46438-40
D-42897 Remscheid
E-Mail: info@swstahl.de
BEDIENUNGSANLEITUNG
www.swstahl.de
7
REPARATIONS
Any hydraulic jack found to be damaged in any way, is found to be worn or operates abnormally, believed to
have subjected to an abnormal load, shall be REMOVED FROM SERVICE UNTIL FULL REPAIRED.
Owners and/or operators should be aware that repair of the equipment requires specialized knowledge and
facilities. Only factory authorized parts, labels and decals shall be used on this equipment. Contact customer
service department.
WARNING!
• READ, STUDY AND UNDERSTAND ALL WARNINGS AND OPERATION INSTRUCTIONS
PRIOR TO USE.
• DO NOT OVERLOAD THIS JACK BEYOND THE RATED CAPACITY.
• THIS JACK IS DESIGNED FOR USE ONLY ON HARD LEVEL SURFACES CAPABLE OF
SUSTAINING THE LOAD. USE ON OTHER THAN HARD LEVEL SURFACES CAN RESULT
IN JACK INSTABILITY AND POSSIBLE LOSS OF LOAD.
• THIS IS A LIFTING DEVICE ONLY. IMMEDIATELY AFTER LIFTING, SUPPORT THE
VEHICLE WITH JACK STANDS.
• DO NOT GET UNDER OR ALLOW ANYONE UNDER THE VEHICLE UNTIL IT HAS
BEEN SUPPORTED BY JACK STANDS.
• DO NOT MOVE OR DOLLY THE VEHICLE WHILE ON THE JACK.
• LIFT ONLY ON AREAS OF THE VEHICLE AS SPECIFIED BY THE VEHICLE
MANUFACTURER
• CENTER LOAD ON SADDLE PRIOR TO LIFTING.
• NO ALTERATIONS TO THE JACK SHALL BE MADE.
• FAILURE OR HEED THESE WARNINGS MAY RESULT IN PERSONAL INJURY AND
PROPERTY DAMAGE.
• THE PRESSURE VALVE HAS BEEN SEALED BY THE FACTORY. NEVER ADJUST
THE PRESSURE VALVE BY YOUR SELF OTHERWISE YOU LOOSE YOUR
GUARANTEE-RIGHT. CONTACT CUSTOMER SERVICE DEPARTMENT TO LET SEAL
THE PRESSURE VALVE BY AUTHORIZED PEOPLE AT 3 TONS LIMITED ONLY.
Because of potential hazards associated with the misuses of equipment of this type, no alterations shall be
made to the product without written authorization of KRAFTWERK as manufacturer and supplier.
ASSEMBLING OF JACK
Please check that you have got all the parts listed below:
- Jack
- Pumping handle in two parts
First, remove the retaining clip:
Press the handle socket down and then pull the retaining clip
out from the hole in the base (as pictured).
HANDLE ASSEMBLY
A) Assemble the handle by inserting the upper handle into the lower handle. The detent ball will lock the
two pieces together.
B) Remove the handle socket screw from the handle socket, put pump handle into the handle
socket hole engaging the universal joint of the release valve. Ensure the handle is seated
completely into the socket then tighten the handle socket screw.
Reparations
Warning!
Assembling of jack
Handle assembly
SW-Stahl GmbH
An der Hasenjagd 3
D-42897 Remscheid
Tel. +49 (0) 2191 / 46438-0
Fax +49 (0) 2191 / 46438-40
E-Mail: info@swstahl.de
BEDIENUNGSANLEITUNG
www.swstahl.de
7
REPARATIONS
Any hydraulic jack found to be damaged in any way, is found to be worn or operates abnormally, believed to
have subjected to an abnormal load, shall be REMOVED FROM SERVICE UNTIL FULL REPAIRED.
Owners and/or operators should be aware that repair of the equipment requires specialized knowledge and
facilities. Only factory authorized parts, labels and decals shall be used on this equipment. Contact customer
service department.
WARNING!
• READ, STUDY AND UNDERSTAND ALL WARNINGS AND OPERATION INSTRUCTIONS
PRIOR TO USE.
• DO NOT OVERLOAD THIS JACK BEYOND THE RATED CAPACITY.
• THIS JACK IS DESIGNED FOR USE ONLY ON HARD LEVEL SURFACES CAPABLE OF
SUSTAINING THE LOAD. USE ON OTHER THAN HARD LEVEL SURFACES CAN RESULT
IN JACK INSTABILITY AND POSSIBLE LOSS OF LOAD.
• THIS IS A LIFTING DEVICE ONLY. IMMEDIATELY AFTER LIFTING, SUPPORT THE
VEHICLE WITH JACK STANDS.
• DO NOT GET UNDER OR ALLOW ANYONE UNDER THE VEHICLE UNTIL IT HAS
BEEN SUPPORTED BY JACK STANDS.
• DO NOT MOVE OR DOLLY THE VEHICLE WHILE ON THE JACK.
• LIFT ONLY ON AREAS OF THE VEHICLE AS SPECIFIED BY THE VEHICLE
MANUFACTURER
• CENTER LOAD ON SADDLE PRIOR TO LIFTING.
• NO ALTERATIONS TO THE JACK SHALL BE MADE.
• FAILURE OR HEED THESE WARNINGS MAY RESULT IN PERSONAL INJURY AND
PROPERTY DAMAGE.
• THE PRESSURE VALVE HAS BEEN SEALED BY THE FACTORY. NEVER ADJUST
THE PRESSURE VALVE BY YOUR SELF OTHERWISE YOU LOOSE YOUR
GUARANTEE-RIGHT. CONTACT CUSTOMER SERVICE DEPARTMENT TO LET SEAL
THE PRESSURE VALVE BY AUTHORIZED PEOPLE AT 3 TONS LIMITED ONLY.
Because of potential hazards associated with the misuses of equipment of this type, no alterations shall be
made to the product without written authorization of KRAFTWERK as manufacturer and supplier.
ASSEMBLING OF JACK
Please check that you have got all the parts listed below:
- Jack
- Pumping handle in two parts
First, remove the retaining clip:
Press the handle socket down and then pull the retaining clip
out from the hole in the base (as pictured).
HANDLE ASSEMBLY
A) Assemble the handle by inserting the upper handle into the lower handle. The detent ball will lock the
two pieces together.
B) Remove the handle socket screw from the handle socket, put pump handle into the handle
socket hole engaging the universal joint of the release valve. Ensure the handle is seated
completely into the socket then tighten the handle socket screw.
Reparations
Warning!
Assembling of jack
Handle assembly
SW-Stahl GmbH
An der Hasenjagd 3
D-42897 Remscheid
Tel. +49 (0) 2191 / 46438-0
Fax +49 (0) 2191 / 46438-40
E-Mail: info@swstahl.de
