background image

 

SW-Stahl und Werkzeugvertriebs GmbH 

Tel. +49 (0) 2191 / 46438-0 

www.swstahl.de 

Leverkuser Straße 65 

Fax +49 (0) 2191 / 46438-40 

D-42897 Remscheid 

E-Mail: info@swstahl.de 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
      
 
 
 
 
 
 
 
 

- 7 - 

5. During charging, the charging lamp (green) 

will  start  flashing.  When  charging  is 
completed, an internal electronic switch will 
automatically  be  triggered  to  prevent 
overcharging. 

-  Charging  will  not  start  if  the  battery  pack  is 

warm.  For  example,  immediately  after 
heavy-duty  operation.  The  yellow  standby 
lamp will be flashing until the battery cools 
down. 

6.  If  the  temperature  of  the  battery  pack  is 

0oC  or  less,  charging  takes  longer  to  fully 
charge  the  battery  pack  than  the  standard 
charging  time.  Even  when  the  battery  is 
fully  charged,  it  will  have  approximately 
50% of the power of a fully charged battery 
at normal operation temperature. 

7.  Once  the  battery  is  fully  charged,  the  

green  lamp  will  be  lit  to  indicate  the  gone 
into a trickle charge mode. 

 
Ni-MH Battery Pack 
When you charge the battery pack for the first 

time,  or  after  prolonged  storage,  charge  it 
for about 24 hours to bring the battery up to 
full capacity. 

 
Li-ion Battery Pack   
Your  battery  pack  is  not  fully  charged  at  the 

time  of  purchase.  Be  sure  to  charge  the 
battery before first use. 

Charging the battery - 
 for Li-ion/ Ni-MH battery  
 

  When charging a cool battery pack (below 

0°C  (32°F))  in  a  warm  place,  leave  the 
battery pack at the place and wait for more 
than  one  hour  to  warm  up  the  battery  to 
the  level  of  the  ambient  temperature. 
Otherwise  battery  pack  may  not  be  fully 
charged. 

  Cool  down  the  charger  when  charging 

more than two battery packs consecutively. 

  Do not insert your fingers/nails into contact 

hole,  when  holding  charger  or  any  other 
occasions. 

1. Place charger in a relatively cool and well-

ventilated area. 

2. Plug charger into the AC outlet.   
    
   CAUTION:  

Ensure that the power source to be utilized 
conforms  to  the  power  requirement 
specified on the product nameplate. 

3.  Turn  the  battery  up-side-down  and  slide 

the  battery  into  charger  while  keeping  the 
alignment marks line up. Slide the forward 
in the direction of the arrow.  Do not force 
battery  as  it  should  slide  easily  into  place 
with  nominal  force.  Any  difficulty  doing  so 
would indicate an incorrect alignment. 

4.  If  the  power  lamp  (red)  does  not  light 

immediately  or  goes  out  soon  after  the 
charger 

is 

plugged 

in, 

consult 

an 

authorized dealer. 

 

Summary of Contents for S3201













Reviews: