Swagelok MS-TBE-1 series User Manual Download

Page: 5 / 16

– 5 –

Tube Bender Technical Data

BENDING RANGE:

1° to 110°, in 1° increments.

Bending in excess of 110° may damage bender.

DIMENSIONS:

Vertical Position: 44 in. (112 cm) high, 29 in. (74 cm) wide, 30 in. (76 cm) deep

WEIGHT:

420 lb (191 kg)

POWER REqUIREMENTS:

MS-TBE-1 MS-TBE-2

115 V (ac) 50/60 Hz

230 V (ac) 50/60 Hz

Maximum current: 13 A

Maximum current: 7 A

Tubing Information

•  All tubing should be free of scratches and suitable for bending.
•  Bends 1, 1 1/4, 1 1/2, and 2 in.; 25, 32, 38, and 50 mm OD tubing in a variety of wall thicknesses.
•  Carbon steel tubing should be soft (annealed), seamless (ASTM A179), or welded and drawn, DIN 2391-1 and

DIN-2391-2 or equivalent, with a hardness of 72 HRB, HV (VPN) 130 or less.

• Stainless steel tubing should be fully annealed, seamless, or welded and drawn, meeting ASTM A269, ASTM A213,

EN-ISO-1127, or equivalent specification, with a hardness of 80 HRB, HV (VPN) 180 or less.

• The following information for bending annealed tubing is listed below in Table 1: bend radius, wall thickness limits,

and minimum straight length required to make a 90° bend using the tail roller.

This bender can be used in the

vertical or horizontal position.

Before using bender make sure rollers and shoe grooves are in line.

See Roller Alignment (page 13).

READ AND BECOME FAMILIAR WITH OPERATING INSTRUCTIONS

BEFORE BENDING TUBING!

Table 1 –

Min/Max Wall Thickness

➀

See the

Swagelok Tubing Data

catalog for suggested tubing wall thickness for use with Swagelok tube fittings.

Tube

in.

Dimensions,

in.

Min

Length

Bend

Radius

Carbon

Steel

Stainless

Steel

20 1/2

0.049/0.120 0.065/0.120

1 1/4

22 3/4

0.065/0.180 0.083/0.156

1 1/2

25 1/2

0.083/0.220 0.095/0.188

0.095/0.220 0.109/0.188

Tube

Dimensions,

Min

Length

Bend

Radius

Carbon

Steel

Stainless

Steel

520

103

1.2/3.0

1.8/3.0

582

126

2.0/4.0

648

152

2.2/4.5

810

203

—

3.0/5.0

Summary of Contents for MS-TBE-1 series

















Search results

Summary of Contents for MS-TBE-1 series

Reviews:

Related manuals for MS-TBE-1 series

Brands by name

Popular brands

Swagelok MS-TBE-1 series, User Manual

Search results

Summary of Contents for MS-TBE-1 series

Reviews:

Related manuals for MS-TBE-1 series

Brands by name

Popular brands