The Outdoorcam camera is designed for use with any TV, VCR, Security Monitor or computer with a video
capture card. The camera has a visual image and can be used indoors or in a sheltered position outside. The
can be used for a variety of purposes including monitoring callers at the door, keeping
your car, yard, shop or warehouse under observation or used as a camera to monitor your baby.
Outdoorcam camera
1.
2.
Camera with Stand and fixed cable
DC Power Adaptor (adaptor design varies depending on country)
1.
2.
3.
4.
5.
Once you have chosen the best position for the camera, switch the power to the
camera off, and unplug the power lead from the camera.
When mounting the Outdoorcam camera to your ceiling or wall, please ensure
that you rotate the camera so that at the top of the camera lens is ‘up’, otherwise
you will find that your pictures are displayed upside down. (see diagram)
Hold the camera base in the position you wish to fix it, and mark the holes with an
appropriate pen or pencil. Once this is done, remove the stand and drill a hole
with the appropriate drill bit for the material you are mounting your camera to and
the screws or fasteners you are using.
Run the camera cable back to the TV/VCR, any holes that you drill need to be at
least / ” (14mm) in diameter to allow the connectors to pass through.
Reconnect the power lead to the camera and switch the camera power back on.
9
16
6.
Position the camera and firmly lock the stand into place. Do not over tighten or
forcefully adjust the camera once it has been correctly positioned.
1
2
Your
is designed to transmit high quality color or black and white(depends on model
purchased) images during daylight and B&W images at night to your television. To help guide you through the
process of setting up the
, we have outlined the steps and numbered each of the
components required in the diagram below.
Outdoorcam camera
Outdoorcam camera
* To extend the operating distance from your TV or VCR you will need to purchase an A/V extension cable
(sold separately) which are available at most electronics stores.
: We do not recommend extending the cable length past
100 metres with a single cable run to avoid loss of signal.
Multiple cable sections connected to make up one cable length will drastically reduce the video signal run distance.
Note
330 Feet/
YELLOW
VCR, TV or MONITOR
OUT
IN
VIDEO
VIDEO
AUDIO
AUDIO
VIDEO IN
2
BLACK
POWER
CONNECTOR
3
4
1
CAMERA
POWER
ADAPTOR
5
Step 1:
Step 2:
yellow
"Video In"
Step 3:
black
black
power adaptor
Step 4:
power adaptor
Step 5:
A/V TV
TV
AV
TV
VCR
VCR
A/V Input
TV
VCR
Note:
Note:
instructions
VCR
TV
A/V inputs.
At the end of your Outdoorcam camera cable you will find two colored plugs:
•Yellow (Video RCA)
•Black (DC Power)
Plug the
RCA plug (1) into the
input (2) (usually located at the back of your TV
or VCR).
Connect the
plug (3) at the end of your Outdoorcam camera into the
plug at the end
of the
(4).
Plug the
(5) into the mains power point in your wall.
If you have an
with RCA sockets you will need to switch the
to the
channel on
your
to view the camera. To connect the Outdoorcam camera to your
, you will need to
turn the
to the
selection and turn your
onto the channel you would normally
use to view a tape or movie on your
. This channel may be activated by a button on your
remote that is marked with this symbol
, or
or
or possibly
or
.
The Outdoorcam will automatically turn on the Infra-Red LEDs when available light is too low to
support a clear picture.
Please read the
for your
or
for more information on using their
L
L2
AV
AV2
1
1
Installation Instructions
Contents and Parts Identification
How to connect Outdoorcam camera to your TV or VCR
2
How to connect Outdoorcam camera to your TV or VCR
Mounting the camera on your wall or ceiling
3
