21
20
Regenerative Cartridges - User manual
Regenerative Cartridges - User manual
Explanations to Figures 1 and 2
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
H
I
I
J
J
K
K
L
L
Swardman
15.11.2018
Designed by
Checked by
Approved by
Date
1 / 1
Edition
Sheet
Date
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
H
I
I
J
J
K
K
L
L
Swardman
15.11.2018
Designed by
Checked by
Approved by
Date
1 / 1
Edition
Sheet
Date
Fig. No. 1 - Swardman Edwin
1
3
2
4
5
6
7
1
Cartridge handle
2
Side cover
3
Cartridge left securing screw
4
Cartridge clutch
5
Cylinder/reel drive V-belt (Edwin) / Cylinder/reel drive cog belt (Electra)
6
Cartridge right securing screw
7
Cartridge pulley
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
H
I
I
J
J
K
K
L
L
Swardman
15.11.2018
Designed by
Checked by
Approved by
Date
1 / 1
Edition
Sheet
Date
Fig. No. 2 - Swardman Electra
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
H
I
I
J
J
K
K
L
L
Swardman
15.11.2018
Designed by
Checked by
Approved by
Date
1 / 1
Edition
Sheet
Date
1
3
2
4
5
6
7
Installation of regenerative cartridges
1. Loosen the mowing height lock screw on the right side of the machine
2. Use the height setting lever to set the mowing height to maximum
3. Remove the side cover of the machine
2
4. Release manually the V-belt (Edwin)
5
or cog belt (Electra)
5
from the cartridge pulley
7
.
5. Using the Allen key, loosen and remove the left
3
and the right securing screw
6
of the cartridge (the key is
included)
6. Remove the cartridge from the machine using the cartridge handle
1
7. Using the handle
1
insert the desired verticutter / scarifier / rotary brush cartridge in the machine
8. Reinstall the securing screws - the left
3
as well as the right one
6
(make sure the screw can be screwed easily)
9. Install the V-belt (Edwin)
5
or the cog belt (Electra)
5
on the cartridge pulley
7
10. Guide the V-belt under the cartridge clutch
4
into its original position and at the Electra under the tensioner
11. Install the side cover
2
12. Set the correct working height of the machine.
a. for the verticutter set the height so that the front roller is maximum 5 mm (0.2in), preferably 3 mm (0.1in),
lifted in the air, and always so that it moves freely above a hard surface. This corresponds to a working depth
of -3 mm (-0.1in) and deeper.
b. for the scarifier set the height so that the springs slightly touch the hard surface or move over it. This
corresponds to a working depth of 0 mm/in and deeper.
c. for the rotary brush lower the working height of the machine so that the bristles are in moderate contact
with the surface / lawn. Replace the protective cover Fig. 3 and then cover the gap between the mower
chassis and the protective with the magnetic shield Fig. 4
13. After installation of the verticutter or scarifier cartridge, place the grass box (for the verticutting cartridge, the
collection into the box is less effective, but the bin serves as a protection against flying objects). After installing
the rotary brush, the grass bin is not installed.
14. The machine is then ready for work. In the case of the installation of the rotary brush according to Fig. 5
obr. č. 5
Fig. 4
Fig. 3
