background image

 

 

 

Caution and safety precautions 

 

 

Never  use  any  other  charger  than  the  supplied  or  a  type  approved  by  Swiss  Timing.  This  could 
destroy  the  battery,  cause  damage  to  unit,  and  possible  cause  personal  injury  due  to  fire  or/and 
electrical shock. 

 

Never  bypass  a  power  cord  ground  lead  by  breaking  off  the  ground  pin,  or  by  using  inappropriate 
extension cords or adapters. 

 

Never  plug  a  power  cord  into  the  AC  power  source  until  you  have  made  sure  that  all  installation, 
cabling and power levels, are proper, and that the applicable procedures in this  manual have been 
followed.  

 

Protect the equipment against splashing, rain and excessive sun rays.  

 

Never use the device if it is damaged or insecure.  

 

Verify the selection of the power distribution. 

 

Verify that the voltage quoted on the rating plate is the same as your voltage. Connect the appliance 
only to power sockets with protective earth. The use of incorrect connection voids warranty.  

 

This program may be modified at any time without prior notification. 

 

Do not open the case; there is nothing that needs servicing inside it. Nevertheless, if the case must 
be  opened,  you  must  call  for  some  qualified  personnel.  The  power  supply  cable  must  be 
disconnected before opening the case. 

 

During  the  transport  of  all  Swiss  Timing  equipment  delivered  with  a  reusable  carry  case,  the  said 
case should be used at all times. This is imperative to limit the damage, such as shocks or vibration 
that can be caused to the units during transport. 

 

The  same  cases  should  also  be  used  when  returning  equipment  to  Swiss  Timing  for  repair.  Swiss 
Timing reserves the right to refuse all guarantees if this condition is not fulfilled.  

 

If the installation includes a horn, be sure to maintain a sufficient security distance from the public. 

 
 
 
 
 
 
 

Documentation Updates 

Swiss Timing Ltd. reserves the right to make improvements in the products described in this documentation 
at  any  time  without  prior  notice.  Furthermore,  Swiss  Timing  Ltd.  reserves  the  right  to  revise  this 
documentation  in  its  content  at  any  time  and  without  any  obligation  to  notify  any  person  or  organization  of 
such revision.   
 

Disclaimer 

The  information  provided  in  this  documentation  has  been  obtained  from  sources  believed  to  be  reliable, 
accurate and current. However, Swiss Timing Ltd. makes no representation or warranty, express or implied, 
with respect, but not limited to, the completeness, accuracy, correctness and actuality of the content of this 
documentation.  Swiss  Timing  Ltd.  specifically  disclaims  any  implied  warranty  of  merchantability,  quality 
and/or  fitness  for  any  particular  purpose.  Swiss  Timing  Ltd.  shall  not  be  liable  for  errors  contained  in  this 
documentation or for incidental or consequential damages in connection with the supply, performance or use 
of this documentation. 
 

Environment 

This symbol indicates that this product should not be disposed with household waste. It has to be 
returned to a local authorized collection system. By following this procedure you will contribute to 
the  protection  of  the  environment  and  human  health.  The  recycling  of  the  materials  will  help  to 
conserve natural resources. 
 

Copyright  

© Swiss Timing Ltd.  
All rights reserved.  
This documentation may not, as a whole or in part, be copied, translated, reproduced, transmitted or reduced 
and/or stored to any electronic medium or machine-readable form without the prior written consent of Swiss 
Timing Ltd. 

 

Summary of Contents for SWISS TIMING 3454.013






















Reviews: