23
Positioning/Fitting
Dependant upon the child seat type, the
most suitable position for the child seat to be
fitted may be the front passenger seat of the
cab (NOTE airbag advice on following page)
The central seat on the rear bench seat is
not suitable for an ISOFIX child seat. Advice
should always be taken from the retailer on
the suitability and security of the seat in the
campervan. Read and follow the child seat
manufacturer’s instructions for fitting the seat.
All Swift campervans are fitted with inertia reel
seat belts, however, the child seat must be tight
in the adult seat. Push all your weight into the
child seat as you tighten the belt.
Keep a copy of the child seat fitting instruction in
the campervan for easy reference.
Any doubts, ask an advisor to show you how to
correctly install the seat.
3.8 Airbag
Never fit a rear facing child restraint in a seat
with an active airbag in front of it.
Forward-facing child restraints should be
positioned as far back from the airbag as
possible. Check the base vehicle handbook.
WARNING:
Extreme Hazard! Never use
a rearward facing child restraint on a seat
protected by an active airbag in front of it.
Death or serious injury to the child can occur.
WARNING:
You must switch the passenger
airbag off when using a rearward facing child
restraint on the front seat.
WARNING:
You must switch the passenger
airbag on following the removal of the child
restraint.
3.9 Three point seat belts
This section refers to the seat belts located in
the habitation area of your campervan.
Dedicated Travelling Passenger Seating
Bench Seat
WARNING:
No passengers are allowed to
stay inside the vehicle whilst moving unless
they are seated in the designated seated
positions. (3 rear positions are available).
For the safety of rear seated passengers, the
bench seat must be correctly installed in to
the guide rails and locked in place in one of the
traveling positions while the vehicle is moving
to avoid any issues when breaking.
All passengers must be buckled up correctly.
To ensure the correct functioning of the seat
belts the bench seat must be securely fastened
in to the running rails and the seat be locked into
one of the travelling positions.
Moving the bench seat
There are two methods to adjust the position
of the seat. By moving the seat with your body
(seated on the seat as in a car seat) or by
pushing it by hand while stood near to the front
of the seat.
Lift the front bar handle and pull or push in the
direction required. Let go of the handle and
the seat will click into the nearest lockable
traveling position. When travelling we would
recommended that any luggage is stored
behind the bench seat and not between the
front and rear seats. To ensure the mechanism
runs smoothly it is recommended to clean and
remove obstacles from the rails.
To lock the seat in the desired position depress
the lever on both sides of the seat.
i
Note:
The forward most lockable position
for the rear seat, in the floor rails, is not
suitable for passengers when travelling.
P
R
EP
AR
IN
G F
OR T
HE R
O
AD
Summary of Contents for MONZA CAMPERVAN 2022
