64
FI
T
T
ED EQ
UIP
MEN
T
9.1 Getting to know EasyStart Pro
Heating Controls
Your Camper van has been fitted with an
Eberspacher Diesel heating system and a easy-
start controller.
The Heater is situated under the vehicle with
the louvered outlet mounted on the rear of the
passenger seat.
It can be rotated to direct the heat to the area
required.
The controls for the heater are mounted on the
Control panel at the corner of the Sink top.
Please refer to the full operating instructions
within the document folder. Also use the QR
code below to access it electronically.
https://www.butlertechnik.com/downloads/
Eberspacher_EasyStart_PRO_-_Operating_
Instruction_Guide.pdf
EasyStart Pro has a simple operating structure.
All settings, functions and parameters are
controlled with a single operating button.
Description of the operating
components
Display
The display shows the following parameters:
• Current operating mode
• Current interior temperature
• Operating mode
• Timer positions
• Settings
• Error codes
Operating button
• The operating button is used to operate, select
and program all the functions and val ues in
EasyStart Pro. The operating button can be
turned and pressed.
- Turning selects a value/function within a
menu.
- Turning to the right increases a value or
selects the next menu item to the right.
- Turning to the left decreases a value or
selects the next menu item to the left.
- Pressing confirms the flashing menu item or
value on the display.
- If EasyStart Pro is in sleep mode (display
OFF), pressing or turning “wakes up” the
active mode. If the heater is switched off,
the Start mask is displayed. If the operator
makes no inputs, an overview mask is
displayed before the system goes to sleep
mode.
- When the heater is running, the last mask is
displayed.
i
Note:
• A LONGPRESS (min. 2 sec.) immediately
starts all connected heaters. The standard
operating time here is set at the factory to 30
minutes.
• During operation, a LONGPRESS (min. 2
sec.) immediately switches off all connected
heaters.
• If terminal 58 has voltage, sleep mode will
not be activated.
LED ring
• The LED ring with its different colours serves
to indicate the operating mode.
- Red ring:
Heating mode
- Blue ring:
Ventilator mode
- Orange ring:
Residual heat mode
- White ring:
System configuration
- Red flashing ring: Fault in one of the
connected heaters or in
EasyStart Pro
Summary of Contents for MONZA CAMPERVAN 2022
