66
FI
T
T
ED EQ
UIP
MEN
T
Flashing function / flashing value
• Select the flashing function in the menu bar by
pressing the operating button.
• Increase or decrease the flashing value by
turning the operating button. Then confirm
the selected value by pressing the operat ing
button.
Cancel / exit settings
Every setting can be cancelled or exited by
pressing the BACK button
i
Note:
Settings and changes must always be con-
firmed by pressing the operating button,
otherwise they will be lost.
Setting the operating time
The operating time can be set individually using
the operating button.
• Turning to the right increases the operat ing
time.
• Turning to the left decreases the operating
time.
• Setting range for the operating time:
min. 10 minutes to max. 120 minutes in one
minute steps.
• The operating time can be prolonged to 720
minutes. Above the 120th minute, the input is
made in 60-minute steps. To do this, please
contact the installation workshop.
i
Note:
• Continuous heating mode is additionally
possible for air heaters.
• The operating times of all connected heaters
can be set independently of one another.
Operating modes
Heat
In this operating mode, the heater heats the
vehicle engine via the coolant circuit and the
vehicle interior via the ventilation louvres,
irrespective of the configuration.
Ventilate
In this operating mode, the heater supplies
the vehicle interior with fresh outdoor air via
the ventilation louvres. This operating mode is
only possible if the function is supported by the
heater version (see also Technical Description of
the Heater).
Temperature sensor
EasyStart Pro has an integrated temperature
sensor that measures the vehicle interior
temperature. During installation, an additional
external temperature sensor can be connected
and integrated into the system.
With air heaters, the temperature sensor
installed in the heater for control of the heater
can also be used to measure the vehicle
interior temperature. This will be configured
by the installing workshop during initial
commissioning.
Further devices
EasyStart Pro allows the simultaneous
operation of up to 4 heaters or, for example,
also a stationary air conditioner. It is also
possible to combine a heater with a fan. The
fan is then used to circulate the air inside the
vehicle. All connected systems can be operated
simultaneously or independently of one another.
i
Note:
The number of symbols and displays differs
depending on the installed heater and feature
options.
Factory setting
Timer mode (for all heaters)
• Weekday group: Mon - Fri
• Departure time: 07:00 h
Air heaters
• Operating time: 30 minutes
• Target temperature: 22°c / 72° F
i
Note:
In the interest of safety, replacement
parts for an appliance shall conform to the
appliance manufacturer’s specifications and
should be fitted by them or their authorised
agents.
Summary of Contents for MONZA CAMPERVAN 2022
