background image

 

Preface 

1.  All internal technologies of this product are protected, including device, software and trademark. 

Reproduction in whole or in part without written permission is prohibited. 

2.  All brands and trademarks of SWIT Electronics Co., Ltd. are protected and other relative 

trademarks in this user manual are the property of their respective owners. 

3.  Due to constant effort of product development, SWIT reserves the right to make changes and 

improvements to the product described in this manual without prior notice. 

4.  The warranty period of this product is 2 years, and does not cover the following:   

(1) Physical damage to the surface of the products, including scratches, cracks or other damage to 

the LCD screen or other externally exposed parts; 

(2) The LCD dot defects are not over three;   

(3) Any damage caused by using third-party power adaptors; 

(4) Any damage or breakdown caused by use, maintenance or storage not according to the user 

manual. 

(5) The product is disassembled by anyone other than an authorized service center. 

(6) Any damage or breakdown not caused by the product design, workmanship, or manufacturing 

quality, etc. 

  Any sales personnel have no rights to provide additional warranty. 

5.  For any suggestions and requirements on this product, please contact us through phone, fax, 

Email, etc. 

 

 

 

 

 

 

 

 

SWIT Electronics Co., Ltd. 

Address: 10 Hengtong Road, Nanjing Economic and Technological Development Zone, 
         Nanjing 210038, P.R.China 
Phone: +86-25-85805753 
Fax: +86-25-85805296 
Email: contact@swit.cc 
http://www.swit.cc 

 

Summary of Contents for S-1093H





















Reviews: