2 0 6 3 6 5 R e v. 8 0 9 U F S . 1 0 . 8 0 9 . 7. U
8 . 2
|
S P A F E N G S H U I
O P E R A T I O N
Check that the power is connected.
Turn on the unit using the ON/OFF switch
and activate it by following the instructions
on the LCD display.
Ensure that a container is located under
the drain hose at the foot end of the
unit to catch excess condensation.
IMPORTANT:
Everyday, before putting your first user in the
machine, we recommend that you run a Warm-Up session with the
Spa Feng Shui 2G System (10 minutes with Steam and
Radiant Heat–already preprogrammed) in order to prepare
the capsule and to clear any residue that might be
remaining in the water ducts.
8 . 3
|
H O W T O R U N Y O U R F I R S T
WA R M - U P S E S S I O N
Main Menu
Select the “Warm-Up” Option:
Select the Warm-Up program with the motion buttons (UP,
DOWN, LEFT, RIGHT) until Warm-Up (blue box) is highlighted.
Confirm your selection by pressing ENTER (see Figure 1).
The Spa Feng Shui 2G System automatically warms up the unit
within 7 minutes. The timer will count down until the Warm-Up
session is finished. Once the Warm-Up session is finished,
“READY” will be displayed on the LCD screen and the Spa Feng
Shui 2G System will inform you with two beeps.
Once “READY” is displayed press the ENTER button to go to the
main menu screen.
To cancel the Warm-Up program at any time press the ESCAPE
button (see Figure 1) and follow the instructions from LCD screen.
8 . 4
|
W O R K I N G W I T H T H E
O P T I O N S
Set the “Settings”
Move with the motion buttons until the Settings box is highlighted
and confirm your selection with the
ENTER
button (see Figure 2).
From the Settings submenu, verify that all settings are correct and
make any necessary corrections. The submenu will allow you to
verify/change the following setting parameters:
Version of program
V XXXX*
Version of program
V XXXX*
Machine type
Spa-FENG SHUI
Temperature
Celsius
(Celsius/Fahrenheit)
Control
Local
(Local / Ethernet)
Control
Display Control
Control
Volume
*XXXX represents the version of your specific machine.
To move up/down in the submenu, use the
UP
or
DOWN
buttons (see Figure 1). To select different settings use the
LEFT
or
RIGHT
buttons.
Verify that all settings are correct and set your selections with the
ENTER
button. The Spa Feng Shui 2G System will automatically
save all of your settings into the memory.
“Service” Sub-Menu
Move with the motion buttons until the Service box is highlighted
and confirm your selection with the ENTER button (see Figure 1).
From the Settings submenu, verify that all settings are correct and
make any necessary corrections. The submenu will allow you to
verify/change the following setting parameters:
Vibratory bed
OFF
(ON / OFF)
Drainage
OFF
(ON / OFF)
Open aroma tank
OFF
(ON / OFF)
Total time
000,00
Move with up/down in the submenu, use the
UP
or
DOWN
buttons (see Figure 1). To select different settings, use the
LEFT
or
RIGHT
buttons. To go back to the previous menu, press the
ESCAPE
button.
VIBRATORY BED —
The vibratory bed can be activated without
any preset programs.
DRAINAGE —
To maintain your Spa Feng Shui 2G System and
ensure maximum productivity from the steam generator and
heating element, it is necessary to flush the steam generator
system at least once a week.
S p a F e n g S h u i - P a g e 2 0
Owner’s Manual
SECTION 8 |
Operation
1
2
3
( Figure 2)
Esc. Ent.
PROGRAM WARM-UP
SETTINGS
SERVICE
LANGUAGE
INSTALL
Spa Feng Shui Manual 809.qxp:DL_SFS_806 A4 NS 9/18/08 4:16 PM Page 24
