background image

- 25 -

EN

9I03

This function enables you to set a recording length
simply by pressing the REC/OTR button on the
TV/VCR.

Make sure ...

TV/VCR power must be turned on.

Insert a cassette tape with its erase prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)

NOTES:

This function CANNOT be done from the remote
control.

Recording starts immediately when the REC/OTR
button is pressed.

When the REC/OTR button is pressed 18 times, the
TV/VCR returns to the Normal Recording mode.

To stop the OTR operation, press the STOP button
on the TV/VCR or on the remote control.

To show the remaining time, press the DISPLAY
button on the remote control so that “OTR”
appears on the TV screen. (It will show up momen-
tarily then disappear.)

Recording stops when 0:00 is reached.

Please note that in the SLP mode maximum record-
ing time, assuming the tape is started at the begin-
ning, is 8 hours using T-160 (or 6 hours using T-120).

If the tape runs out before the end time, the
TV/VCR will switch to the Stop mode immediate-
ly, ejects the tape and turns itself off.

1

Select the channel to be recorded

Press the number buttons on the remote control or the
CHANNEL

K

or 

L

button.

Remember:

If the TV/VCR is connected to a cable

box or satellite box, the TV/VCR must be on CH3 or
CH4, then the channel to be recorded is selected on
the cable box or satellite box.

2

Select the tape speed

Press the SPEED button to select the desired tape
speed (SP/ SLP).

3

Begin OTR

Press the REC/OTR button on the
TV/VCR as many times as needed.
The recording length will be deter-
mined by the number of times you
press the REC/OTR button. Each additional push will
increase the recording time by 30 minutes. It is set up
to 8 hours.

OTR (One Touch Recording)

Push(es)

Display

Recording length

1 push

(normal recording)

2 pushes

0:30

30 minutes

3 pushes

1:00

60 minutes

17 pushes

8:00

480 minutes

You can make copies of video tapes made by friends
or relatives for your enjoyment.

Connect your TV/VCR and a Source (Playing) VCR
using the following diagram.

1)Insert a pre-recorded video cassette into the Source

(Playing) VCR or camcorder.

2)Insert a blank video cassette, or one you want to

record over, into the TV/VCR’s cassette compart-
ment.

3)Press the SPEED button on remote control for the

TV/VCR to select the desired recording speed
(SP/SLP).

4)Press the CHANNEL

K

or 

L

button on the

TV/VCR until “AUX” appears on the screen.

5)Press the RECORD button on the TV/VCR.
6)Begin playback of the tape in the source (Playing)

VCR or camcorder.

NOTE:

For best results during dubbing, use the

TV/VCR’s front panel controls whenever possible.
The remote control might affect the source (Playing)
VCR’s playback operation.

COPYING A VIDEO CASSETTE

(Requires a VCR or camcorder)

WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.

VIDEO

IN

OUT

AUDIO

AUDIO

VIDEO

[Ex: Source (playing)
VCR or camcorder]

Audio/Video
adapter cable
(not supplied)

[The TV/VCR]

OTR(2 : 30)

SP

Summary of Contents for 6313CCC

































Reviews: