- 16 -
EN
9J27
PLAYBACK
NORMAL PLAYBACK
Make sure ...
•
TV/VCR power must be turned on.
1
Insert a prerecorded tape
If the erase-protection tab has been removed, the
TV/VCR will start playback automatically.
2
To begin playback
Press the PLAY button.
Note:
If any menu is activated on the screen, the
PLAY button does not function. Press the MENU
button to clear the menu. then, press the PLAY button.
3
To stop playback
Press the STOP button when playback is completed.
PRECAUTIONS
•
Avoid moisture. Moisture condensation may occur
on the tape if it is moved from a cold place to a
warm place or visa versa. Before using a tape with
these conditions, to avoid damage of the tape and
your TV/VCR, wait until the tape has warmed to
room temperature and the moisture has evaporated.
•
Avoid extreme heat, high humidity and magnetic
fields.
•
Do not tamper with the cassette mechanism.
•
Do not touch the tape with your fingers.
The TV/VCR has the auto repeat function that allows
you to repeat a tape indefinitely without touching the
PLAY button.
INSERTING A CASSETTE
Insert the cassette in the direction
as shown. Push in gently, but con-
tinuously, on the center-back of the
cassette until it is drawn into the
TV/VCR. The TV/VCR will auto-
matically turn on.
Window
ALL REPEAT:
Repeat playback from the beginning
to the end of the tape.
BLANK REPEAT
: Repeat playback from the begin-
ning to a blank part, which is blank for more than
10 seconds.
1
Select “USER’S SET UP”
Press the MENU button on the
remote control.
Press the PLAY/
K
or STOP/
L
but-
ton to point to “USER’S SET UP”.
Then, press the F.FWD/
B
button.
2
Select “ALL” or “BLANK”
Press the PLAY/
K
or STOP/
L
but-
ton to point to “REPEAT PLAY”.
Press the F.FWD/
B
or REW/
s
but-
ton repeatedly until your desired
selection [ALL] or [BLANK]appears.
3
Exit the Repeat Play setting
Press the MENU button on the remote control to
return to the TV mode.
4
Start playback
Press the PLAY button to start the Repeat Play.
”REPEAT PLAY
B
” appears.
•
Once you select the Repeat Play mode, it stays in
effect even after you turn off the TV/VCR.
•
If the Rental mode is set [ON], the “RENTAL
PLAY
B
” display has priority.
TO CANCEL THE REPEAT PLAY MODE
Repeat steps [1] and [2], select [OFF] using the
F.FWD/
B
or REW/
s
button on the remote control.
Press the MENU button on the remote control to
return to TV mode.
If there is a power failure of any kind, the unit
will retain its memory for this feature.
AUTO REPEAT PLAYBACK
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
CHANNEL SET UP
B
USER’S SET UP
LANGUAGE [ENGLISH]
ZERO RETURN
TIME SEARCH
– USER’S SET UP –
RENTAL
[OFF]
B
REPEAT PLAY
[ALL]
AUTO RETURN
[OFF]
This TV/VCR will operate with any cassette that has the
mark. For best results, we
recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.
This function enables you to receive FM radio broad-
casting.
1
Set the FM mode
Press the TV/FM button on the
remote control. The radio frequen-
cy appears on the TV screen.
2
Select the radio frequency you want to receive
Press the CHANNEL
K
or
L
button until your
desired radio frequency appears.
NOTES:
•
The radio frequency indication repeats to appear
and disappear.
•
You can not record the FM radio wave broadcasting.
•
If you receive a weak radio signal, you may change
the FM Antenna mode to INT(internal) or
EXT(external) by following the step below.
1)Press the MENU button. Press the PLAY/
K
or
STOP/
L
button to point to “CHANNEL SET UP”.
Then, press the F.FWD/
B
button.
2)Press the PLAY/
K
or STOP/
L
button to point to
“FM ANTENNA”. Select [INT] or [EXT] using
the F.FWD/
B
or REW/
s
button.
FM MODE
FM 88.0 MHz
T4304.QX33 02.1.16 3:06 PM Page 16