background image

 

13

 

9. THE BEST WAY TO DRIVE OFF

 

 

Turn on the turn signal light before moving, and make sure no vehicle is coming from behind.   
Then, drive off. 

  THE CONTROL OF THROTTLE VALVE HANDLE   

 

Acceleration

To increase speed.    When riding 

on an inclined road, turn the 
throttle valve handle slowly to 
allow the engine to output its 
power. 

 

Deceleration

To decrease speed. 

 

 
 
 
 

 PARKING METHOD  

 

When approaching the parking lot: 

1. Turn on the turn signal light early, and pay attention to the vehicles in front, from rear, left and right, 

then take the inner lane and approach slowly. 

2. Return the throttle valve handle back to its original position, and apply brakes in advance. (Brake 

light comes on when braking to warn drivers of vehicles behind.) 

 

When stop completely: 

3. Press the turn signal switch back to its original position, and turn the ignition switch key to “OFF” 

position to shut off the engine. 

4. Get off the motorcycle from left side after the engine has been stopped, and select a parking place 

where the motorcycle will not interfere with traffic and the ground is level, then put down 
motorcycle’s main parking stand. 

5. Hold the steering handle with your left hand, and hold down the front end of saddle or hold the 

parking handle on the lower-left side of saddle with your right hand. 

6. Press the main parking stand with your right foot, put down the main parking stand firmly on the 

ground.  

 

To remind you:

 Lock the steering handle and remove the key after parking to prevent the 

motorcycle from being stolen. 

 
 
 
 
 

       

 

CAUTION:

   

 

Park your motorcycle at a safe place where it will not interfere with traffic. 

 

Deceleration 

Acceleration 

Summary of Contents for AK12U Series


























Reviews: