background image

8

 

3. Before riding      4. Safe riding

This manual describes the correct usage of this scooter including safety riding, simple inspection methods 
and so on. 
For a more comfortable and safety riding, please read this manual carefully. 

Thank you very much for your patronage 

In  order  to  maximize  your  scooter’s  performance,  a  periodical  inspection  and  maintenance  should  be 
completely  carried  out.    We  recommend  that  after  riding  your  new  scooter  for  the  first  300  kilometers, 
you  should  take  your  scooter  to  the  original  dealer  for  an  initial  inspection,  and  to  have  your  scooter 
inspected periodically every 1,000 kilometers thereafter. 

 

Ÿ

 

In case the scooter’s specifications and construction are modified and different from the photos and 
diagrams on the owner’s manual/catalogues, the specifications and construction of the actual scooter 
shall prevail. 

4. SAFE RIDING

It is very important to be relax and clothe properly when driving, observe traffic regulations, do not rush, 
always drive carefully and relaxed. 
Usually, most people would ride their newly bought scooter very carefully, but after they became familiar 
with their scooters, they tended to become reckless which may result in an accident. 

  To remind you: 

Ÿ

 

Please wear a safety helmet, and properly tighten the chin belt when riding a scooter. 

Ÿ

 

Clothes with open or loose cuffs may be blown by wind and cause the cuffs to get caught on the 
steering handle and thus affects riding safety. So, put on clothes with tight sleeves. 

Ÿ

 

Hold the steering handle by both hands when riding.    Never ride with only one hand. 

Ÿ

 

Observe the speed limit. 

Ÿ

 

Perform periodical maintenance and inspection in accordance with the schedule. 

 

WARNING!! 

Ÿ

 

To avoid getting burned by exhaust pipe when taking a passenger.    Make sure your passenger has 
put his/her feet on the pedals. 

Ÿ

 

After running, the exhaust pipe is very hot, be careful not to get burned when conducting an 
inspection or maintenance. 

Ÿ

 

After running, the exhaust pipe is very hot, select a suitable location to park your scooter to avoid 
others getting burned by the exhaust pipe. 

  CAUTION: 

Ÿ

 

Modified scooter will affect its structure or performance, and cause poor engine operation or exhaust 
noise, which will result in shortening the scooter’s service life.    Besides, modification is illegal and 
does not conform to the original design and specifications.    A modified scooter will not be covered 
by warranty, therefore, do not modify your scooter at will. 

Ÿ

 

Tire and rim modifications will make it unsafe to ride and may cause severe injury or death. 

Summary of Contents for JET 100 series




































Reviews: