background image

Warning: Changes or modifications to this unit not expressly approved 

by the party responsible for compliance could void the user’s authority 

to operate the equipment.

NOTE: This equipment has been tested and found to comply with the 

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against 

harmful interference in a residential installation. This equipment 

generates, uses and can radiate radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause 

harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a 

particular installation. If this equipment does cause harmful interference 

to radio or television reception, which can be determined by turning the 

equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures:

●Reorient or relocate the receiving antenna.

●Increase the separation between the equipment and receiver.

●Connect the equipment into an outlet on a circuit different from that to  

  which the receiver is connected.

●Consult the dealer or an experienced radio/TV technician for help.

“This device complies with FCC radiation exposure limits set forth for 

general population (uncontrolled exposure).

This device must not be collocated or operating in conjunction with any 

other antenna or transmitter.”

Decoration of Conformity lnserts:

“Hereby, GuangDong Syma model drone lndustrial co.,ltd, declares 

that this drone is in compliance with the essential requirements and 

other relevant provisions of Directive 2014/53/EU.”

A copy of the full DoC is attached.

-13-

Summary of Contents for X20W




















Reviews: