background image

Standards Passed
     Electrostatic Discharge (ESD)

IEC 1000-4-2, Level 3, 6 KV Contact, 8 KV Air

     Radio Frequency Immunity (RFI), 

     Conducted

IEC 1000-4-6, Level 3 10 V/M

     Radio Frequency Immunity (RFI), Radiated IEC 1000-4-3, Level 3 10 V/M
     Fast Transient Burst

IEC 1000-4-4, Level 3, 3.5 KV Input Power

     Surge

          IEC

1000-4-5                                                             

 Level 3, 2 KV Line-to-Line                                

 Level 4, 4 KV Line-to-Ground

        ANSI / IEEE

C62.41 Surge and Ring Wave Compliance to a 

Level of 6 KV Line-to-Line

     Hi-Potential Test

Meets UL508 (2 x Rated V 1000 Volts for 

1 Minute

     Vibration

IEC 68-2-6, 10-55 Hz, 1 mm Peak-to-Peak, 2 

Hours, 3 Axis

     Shock

IEC 68-2-27, 30 G, 3 Axis, 11 mS Duration, Half 

Sine Pulse

MECHANICAL
     Dimensions

3.0” H x 5.1” D x 3.6” W

     Terminal Torque

7 inch/pounds

     Enclosure Material

Polycarbonate

     Weight

1.2 pounds

     Maximum Conductor Size Through Unit

0.65” with insulation

ENVIRONMENTAL

     Temperature Range

Ambient Operating: -20

o

 - 70

o

 C (-4

o

 - 158

o

 F)         

Ambient Storage: -40

o

 - 80

o

 C (-40

o

 - 176

o

 F)

     Pollution Degree

3

     Class of Protection

IP20, NEMA 1

07/25/03 

 

 

 

                 -16-

Summary of Contents for 777-575-FT





















Reviews: