background image

TABLE 6: CIO-EN SPECIFICATIONS 

Ethernet Controller 

Compatibility

IEEE 802.3

Capability

10Base-T

Output Relay Contact Rating – SPDT (1), SPST (1)

 

     Pilot Duty 

480VA @ 240VAC, B300 

     General Purpose 

5A @ 240VAC 

Inputs (4) – General Purpose

 

     

Voltage Range 

12–24VDC 

     Current 

2mA (typical) 

Remote Reset    

(for use with optional
777-P/P1 overload) 

Normally open pushbutton  
rated 24VDC, 10mA (min.) 

Power Requirements

 

     Voltage 

24VDC (+/- 10%) 

     Current 

95mA (max.) 
70mA (typical) 

     Power 

2.28 W (max.) 
1.7 W (typical) 

Weight 

14 oz. 

Enclosure 

Polycarbonate 

Terminal

 (depluggable terminal block) 

     Torque 

3 in.-lbs. (max.) 

     Wire AWG 

12-20 AWG 

Safety Marks

 

     UL 

UL508 (File #E68520) 

     CSA 

C 22.2 

     CE 

IEC 60947 

Standards Passed

 

Electrostatic Discharge (ESD)  

IEC 61000-4-2, Level 3, 6kV contact, 8kV air 

Radio Frequency Immunity, Radiated 

150 MHz, 10V/m 

Fast Transient Burst  

IEC 61000-4-4, Level 3, 4kV input power 

Hi-Potential Test

 

Meets UL508 (2 x rated V +1000V for 1 minute) 

Surge 

Input Power – IEC 61000-4-5, Level 1 
Inputs/Data Lines – IEC 61000-4-5, Level 2 

Environmental

 

     Temperature Range 

Ambient Operating: -20

°

 to 70

°

C (-4

°

 to 158

°

F) 

Ambient Storage: -40° to 80°C (-40° to 176°F) 

     Class of Protection 

IP20 (Finger Safe) 

     Relative Humidity 

10-95%, non-condensing per IEC 68-2-3 

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com

Summary of Contents for CIO-EN









Reviews: