background image

Item No. 53-0018

ARC-2 and ARC-2i Menu ARCs 

Quick Start Guide

© 2009 Symetrix, Inc. All rights reserved. Printed in the United States of America. The information in this document is subject to change without notice. 

Symetrix, Inc. shall not be liable for technical or editorial errors or omissions contained herein; nor is it liable for incidental or consequential damages 

resulting from the furnishing, performance, or use of this material. Mention of third-party products is for informational purposes only and constitutes 

neither an endorsement nor a recommendation. Symetrix assumes no responsibility with regard to the performance or use of these products. Under 

copyright laws, no part of this brochure may be reproduced or transmitted in any form or by any means, electronic or mechanical, without permission 

in writing from Symetrix, Inc. If, however, your only means of access is electronic, permission to print one copy is hereby granted. The following are 

either Trademarks or Registered Trademarks of Symetrix, Inc.: Symetrix, SymNet, SymNet Designer, SymLink and CobraLink. Windows is a Registered 

Trademark of Microsoft, Inc.. Other product names mentioned herein may be trademarks and/or registered trademarks of other companies and are 

property of their respective owners.

6408 216th Street SW 

|

 Mountlake Terrace, WA 98043  USA

T

 +1.425.778.7728  

F

 +1.425.778.7727 

|

 

www.symetrix.co

Summary of Contents for ARC-2













Reviews: