3 of 4
www.symetrix.co
|
+1.425.778.7728
QUICK START GUIDE:
Solus NX 4x4, 8x8, and 16x8
Declaration of Conformity
We,
Symetrix Incorporated
, 6408 216th St. SW,
Mountlake Terrace, Washington, USA, declare under our
sole responsibility that the products:
Solus NX 4x4, 8x8, and 16x8
to which this declaration relates, is in conformity with the
following standards:
IEC 60065 (safety),
EN 55032, EN 55103-2, EN 61000-3-2,
EN 61000-3-3 (EMC-International),
FCC Part 15 (EMC-USA),
RoHS (health/environmental)
The technical construction file is maintained at:
Symetrix, Inc.
6408 216th St. SW
Mountlake Terrace, WA, 98043 USA
The authorized representative located within the European
Community is:
World Marketing Associates
P.O. Box 100
St. Austell, Cornwall, PL26 6YU, U.K.
Date of issue: July 29, 2016
Place of issue: Mountlake Terrace, Washington, USA
Authorized signature:
Julia Ogden, COO, Symetrix Incorporated.
Configuring IP Parameters
Locating Hardware
Discovery of, and connection to, Solus NX
4x4, 8x8, and 16x8 hardware is done with
the Locate Hardware dialog found under the
Hardware menu or by clicking the Locate
Hardware icon in the tool bar or on a particular
Solus NX 4x4, 8x8, and 16x8 unit itself.
IP Configuration with Composer
The Locate Hardware dialog will scan the
network and list available units. Select the Solus NX 4x4, 8x8,
or 16x8 unit you wish to assign an IP address to and click
the Properties button. If you wish to assign Solus NX 4x4,
8x8, or 16x8 a static IP address, select “Use the following
IP address” and enter the appropriate IP Address, Subnet
mask and Gateway. Click OK when finished. Now, back in
the locate hardware dialog, ensure the Solus NX 4x4, 8x8,
or 16x8 device is selected and click “Select Hardware Unit”
to use this Solus NX 4x4, 8x8, or 16x8 hardware in your Site
File. Close the Locate Hardware dialog.
The RJ45 connectors labeled “ARC” are only for use
with the ARC series of remotes. DO NOT plug the ARC
connectors on Symetrix products into any other RJ45
connector. The “ARC” RJ45 connectors on Symetrix
products can carry up to 24 VDC / 0.75 A (class 2 wiring)
which can damage Ethernet circuitry.
ARC Pinout
The RJ45 jack distributes power and RS-485 data to one
or more ARC devices. Uses standard straight-through UTP
CAT5/6 cabling.
!
Warning! Refer to the RJ45 Warning for compatibility
information.
The Symetrix ARC-PSe provides serial control and power
distribution over standard CAT5/6 cable for systems with
more than 4 ARCs, or, when any number of ARCs are
located long distances from a Symetrix DSP unit.
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1 • AUDIO (+)
2 • AUDIO (-)
3 • COMMON GROUND
4 • RS-485 DATA (A)
5 • RS-485 DATA (B)
6 • COMMON GROUND
7 • POWER (+V)
8 • POWER (+V)
Note:
The ARC Audio line may be grounded at the
Symetrix rack-mount device and the ARC wall panel
to provide additional distance.
ARC PORT PINOUT
8
7
6
5
4
3
2
1
Pair 1
Pair 3
Pair 4
Pair 2
- or -
- or -
