56
08/2009 Rev. 0.4
S1000 All in One
S3000 All in One (MAXI)
S1000 / S3000 / S3000 MAXI
08/2009 Rev. 0.4
57
S1000 All in One
S3000 All in One (MAXI)
S1000 / S3000 / S3000 MAXI
Service menu continued….
Main item
Sub item
Sub
Range
Description
2.7 Hardware test
Inputs
Temperature
Boiler temp
Shows the status of the sensors/switches
indicated
Level sensors
High Yes/no
Low Yes/no
Drip tray sensor
Yes/no
Shot 1
Yes/no
Shot 2
Yes/no
Shot 3
Yes/no
Key switch
Yes/no
Outputs
Test by holding
in recipe but-
ton 5.
# During test the
display shows
the Nominal
current (mA)
When the
Nominal current
of a output rises
above the set
current *
mentioned output
will be shut off.
KW1
* 400 mA
Inlet valve (Boiler)
DV1
Dispenser valve 1 (Mixer 1)
DV2
Dispenser valve 2 (Mixer 2)
DV3
Dispenser valve 3 (Mixer 3)
DV4
Dispenser valve 4 (Hot water)
DV5
Not used
DV6
Not used
IM1 #
* 400 mA
Ingredients motor 1 (Cacao cartridge)
IM2 #
Not used
IM3 #
Ingredients motor 3 (Coffee cartridge)
IM4 #
Not used
IM5 #
Ingredients motor 5 (Topping cartridge)
IM6 #
Not used
MM1 #
* 800 mA
Mixer motor 1
MM2 #
Mixer motor 2
MM3 #
Mixer motor 3
Ventilator
* 200 mA
Ventilator
LED’s
Not used
Calib. valves
Test by holding
in recipe button
5 (for 1 sec.)
to open the rel-
evant valve for
10 seconds.
DV1
15 ml / sec
Calibrate to 150 ml (10 sec x 15 ml)
DV2
15 ml / sec
Calibrate to 150 ml (10 sec x 15 ml)
DV3
15 ml / sec
Calibrate to 150 ml (10 sec x 15 ml)
DV4
20 ml / sec
Calibrate to 200 ml (10 sec x 20 ml)
DV5
Not used
DV6
Not used
Service menu continued….
Main item
Sub item
Item
Description
2.8 Read log
Saves last 20 error messages, including date and time
2.9 Clear log
Are you sure?
Clears log
Are you sure?
When a new circuit board is introduced it is necessary to load de-
faults. When loading defaults it must be stated on the Symfoni model
plate. The correct model settings are not loaded until the question
‘Are you sure?’ has been con
fi
rmed.
Attention
:
●
Before you start changing the button- and/or receipt- settings, first
close the service menu, only after re-entering the service menu the
new model settings will be activated.
●
When you con
fi
rm this setting all loaded factory settings and
changed programmed values will be lost.
●
After loading defaults the PIN code reverts to 2-2-2-2-2 and the
language reverts to English. Change if necessary.
2.10 Load defaults
* From software
V3.08 sept 2009
Model
#
S3000
S3000 MAXI
S1000 *
S1000 *
S1000 *
Type code
SY1A xx
SY2A xx
SY3A xx
SY4A xx
SY5A xx
2.11 SD menu
Before saving
or loading data,
insert an empty SD
memory card into
the card reader .
This is located
behind the stainless
steel panel on the
inside of the door.
SD card
speci
fi
cations:
- 16MB or greater
- FAT16 format
Load data
Pers. settings
This menu item is for loading
personal settings
to the device using
an SD memory card. This
fi
le contains the (amended) personal set-
tings for menus:
2.4 Settings / 2/6 Descale-fi lter / 2.13 Additional
settings.
The data
fi
le (Ofxxxx00.mdu) should be on the SD card.
Language
This menu item is for loading a
different language set
to the
device. The data
fi
le (xxxxxx.tlf) should be on the SD card.
Recipe
This menu item is for loading
personal recipes
to the device using
an SD memory card. This
fi
le contains the (amended) personal reci-
pes for menus:
2.1 Quick recipe / 2.2 Button settings / 2.3 Recipe
settings.
The data
fi
le (OFxxxx00.rcu) should be on the SD card.
Save data
Pers. settings
This menu item is for saving
personal settings
to an SD memory
card and copying them to another device.
All settings amended in menus:
2.4 Settings / 2.6 Descale-fi lter /
2.13 Additional settings
are loaded to the SD card in one data
fi
le
(OFxxxx00.mdu).
Recipes
This menu item is for saving
personal recipes
to an SD memory
card and copying them to another device.
All settings amended in menus:
2.1 Quick recipe / 2.2 Button
settings/ 2.3 Recipe settings
are loaded to the SD card in one data
fi
le (OFxxxx00.rcu).
2.12 Change PIN
New PIN code
Repeat PIN code
This menu item is for changing the PIN code using buttons 1-4 only.
The entire service menu is accessed with this PIN code, which
prevents unintentional changes from being made to the machine
settings by untrained staff.
• The ex-factory PIN code is 2-2-2-2-2
PIN code forgotten or needs to be deactivated?
The PIN code input display (operator menu item 1.7) shows a
number on the right. Enter the corresponding PIN code (see list on
p.56) to access the service menu.
Memory Card
Memory Card
