Symmetry TDH14P Assembly Instructions Manual Download

Page: 9 / 9

Hand Control Programming-TDH14P

Version 1

．

October 2018

9 of 9

Error Codes

The digital display shows the error code below to suggest the issues that users may encounter during the operation.

Error code

Descriptions

000

Resetting

E00

Not reset completely

E01

Overuse protection

E02

Unbalance protection

E03

Anti-collision

E04

T-touch Protection

E11

M1 Motor over-current protection

E12

M2 Motor over-current protection

E13

M3 Motor over-current protection

E21

No Hall sensor from M1

E22

No Hall sensor from M2

E23

No Hall sensor from M3

E31

No current from M1

E32

No current from M2

E33

No current from M3

Power Saving Function - Waking up the Control



When no button has been pressed for 25 seconds, display goes off. Press any button to light up the display again.



When no button has been pressed for 30 seconds, the system goes to <0.1W standby mode

(note 2)

. Long press

any button to wake the system up. The digital display will show desk height again.

Note 2: It depends on the control box whether it support 0.1W standby mode or not.

Summary of Contents for TDH14P










Search results

Summary of Contents for TDH14P

Reviews:

Related manuals for TDH14P

Brands by name

Popular brands

Symmetry TDH14P, Assembly Instructions Manual

Search results

Summary of Contents for TDH14P

Reviews:

Related manuals for TDH14P

Brands by name

Popular brands