Symmetry Voyager Assembly Instructions Manual Download

Page: 17 / 17

To report any issues with this product, please contact our customer service department at (888) 552-5699.

For more information, visit www.symmetryoffice.com

VOYAGER

GENERAL CONTROL BOX

Power supply

120 VAC ± 10% / 60 Hz

Standby power consumption, primary

<0.3 W

Operating temperature

0–35º C

Protection class

IP 20

Maximum power output

216VA / 24V

2-LEG FRAME WITH CONTROL BOX

Maximum lift capacity

200 lb (� 90 kg / 890 N)

Adjustable range

18.9"

Maximum input current

6.5 A

Maximum duty cycle

10% (2 minutes on / 18 minutes off)

TECHNICAL DATA

STANDARDS AND CERTIFICATIONS

The drive system is tested according to the following standards:
• UL 962

Issued: 2014/11/07 Ed: 4 Household and Commercial Furnishings

• CSA C22.2#68

Issued: 2009/09/01 Ed: 7 (R2014)

Motor-Operated Appliances (Household and Commercial)

• Meets BIFMA X5.5 2014

WARRANTY

Contact your sales representative for warranty information.

System: Clever

OMT-Veyhl USA

11511 James Street

Holland, MI 49424

Intertek listing belongs to:

Summary of Contents for Voyager


















Search results

Summary of Contents for Voyager

Reviews:

Related manuals for Voyager

Brands by name

Popular brands

Symmetry Voyager, Assembly Instructions Manual

Search results

Summary of Contents for Voyager

Reviews:

Related manuals for Voyager

Brands by name

Popular brands